akaroa1
Member

7027 Likes

Page 121 of 469 First ... 2171107108109110111112113114115116117118119120121122123124125126127128129130131132133134135171221 ... Last

• Jump to page:

1. 
   kristopher liked post by akaroa1 On thread : Another Vintage project and what happens when .....

   So what the BP cast lead load is screaming at me is that the nitro load that only half filled the case is very inconsistent and that the BP load which is 105% full is very consistent I had better...

   Liked On: 14-05-2024, 01:59 PM

2. 
   kristopher liked post by akaroa1 On thread : Another Vintage project and what happens when .....

   I forgot to mention re the Epoxy Acetone clean all the parts prior to final epoxy fitting Mix about 3 or 4 table spoons worth of it to get it well mixed and accurate. Put plenty on as the liner...

   Liked On: 14-05-2024, 01:57 PM

3. 
   kristopher liked post by akaroa1 On thread : Another Vintage project and what happens when .....

   For anyone interested in how this conversion was done here are some missing details on the process I used. There are clearly a lot of little tips and tricks. Just remember when epoxying in a...

   Liked On: 14-05-2024, 01:56 PM

4. 
   gundoc liked post by akaroa1 On thread : Another Vintage project and what happens when .....

   I can confirm that it like Black Powder 360 grain cast powder coated loads. 50 grains 1 1/2 FG and over powder card slightly compressed 250199 250200

   Liked On: 14-05-2024, 12:51 PM

5. 
   Micky Duck liked post by akaroa1 On thread : Another Vintage project and what happens when .....

   I found an old roll of glow tape in my possuming kit. Will cut a tiny strip and try it out when I have time to see if it is overpowering or ok If any good I will go the glow powder and clear nail...

   Liked On: 14-05-2024, 12:26 PM

6. 
   Micky Duck liked post by akaroa1 On thread : Another Vintage project and what happens when .....

   So where do you guys buy your glow in the dark nail polish ? Could also be good on the fore sight 250237

   Liked On: 14-05-2024, 12:26 PM

7. 
   Micky Duck liked post by akaroa1 On thread : Another Vintage project and what happens when .....

   So what the BP cast lead load is screaming at me is that the nitro load that only half filled the case is very inconsistent and that the BP load which is 105% full is very consistent I had better...

   Liked On: 13-05-2024, 06:52 PM

8. 
   Micky Duck liked post by akaroa1 On thread : Another Vintage project and what happens when .....

   I can confirm that it like Black Powder 360 grain cast powder coated loads. 50 grains 1 1/2 FG and over powder card slightly compressed 250199 250200

   Liked On: 13-05-2024, 06:52 PM

9. 
   Ross Nolan liked post by akaroa1 On thread : Another Vintage project and what happens when .....

   I can confirm that it like Black Powder 360 grain cast powder coated loads. 50 grains 1 1/2 FG and over powder card slightly compressed 250199 250200

   Liked On: 13-05-2024, 05:55 PM

10. 
    rugerman liked post by akaroa1 On thread : Another Vintage project and what happens when .....

    This project is complete and test fired IMR 4198 300 grain JHP increasing loads all shot well But even as pressure increased unburned powered stayed high. So some work to do there All two shot...

    Liked On: 13-05-2024, 02:34 PM

11. 
    Micky Duck liked post by akaroa1 On thread : Another Vintage project and what happens when .....

    I forgot to mention re the Epoxy Acetone clean all the parts prior to final epoxy fitting Mix about 3 or 4 table spoons worth of it to get it well mixed and accurate. Put plenty on as the liner...

    Liked On: 13-05-2024, 12:21 PM

12. 
    Micky Duck liked post by akaroa1 On thread : Another Vintage project and what happens when .....

    For anyone interested in how this conversion was done here are some missing details on the process I used. There are clearly a lot of little tips and tricks. Just remember when epoxying in a...

    Liked On: 13-05-2024, 12:21 PM

13. 
    Micky Duck liked post by akaroa1 On thread : Another Vintage project and what happens when .....

    I was running it with a little toilet paper filler because 4198 only half filled the case

    Liked On: 13-05-2024, 12:18 PM

14. 
    makka liked post by akaroa1 On thread : Another Vintage project and what happens when .....

    I forgot to mention re the Epoxy Acetone clean all the parts prior to final epoxy fitting Mix about 3 or 4 table spoons worth of it to get it well mixed and accurate. Put plenty on as the liner...

    Liked On: 13-05-2024, 11:40 AM

15. 
    makka liked post by akaroa1 On thread : Another Vintage project and what happens when .....

    For anyone interested in how this conversion was done here are some missing details on the process I used. There are clearly a lot of little tips and tricks. Just remember when epoxying in a...

    Liked On: 13-05-2024, 11:40 AM

Page 121 of 469 First ... 2171107108109110111112113114115116117118119120121122123124125126127128129130131132133134135171221 ... Last

• Jump to page: