Bill999
Member

1805 Likes

Page 8 of 121 First 1234567891011121314151617181920212258108 ... Last

• Jump to page:

1. 
   Micky Duck liked post by Bill999 On thread : Changing a Remmington 700 from .270 to .308

   if you are patient a 308 rem 700 full rifle will pop up for less than the cost of this whole rebarrel and then you can have two rifles only rebarrel if you need something in a caliber its not...

   Liked On: 24-08-2023, 09:43 AM

2. 
   Barry the hunter liked post by Bill999 On thread : Changing a Remmington 700 from .270 to .308

   if you are patient a 308 rem 700 full rifle will pop up for less than the cost of this whole rebarrel and then you can have two rifles only rebarrel if you need something in a caliber its not...

   Liked On: 24-08-2023, 09:10 AM

3. 
   57jl liked post by Bill999 On thread : tight closing the bolt

   could be too long case lenght and needing a trim could be the decapping ball pulling the shoulder forward a bit on the up stroke (too much friction and needs a bit of lube) could be that the...

   Liked On: 22-08-2023, 11:15 PM

4. 
   Micky Duck liked post by Bill999 On thread : tight closing the bolt

   I found that out the hard way mate but its great to have it confirmed I was necking up to 30 cal after that then back down to 7mm but it wasnt enough only about 3 out of 30 blew primers but...

   Liked On: 21-08-2023, 10:25 PM

5. 
   rewa liked post by Bill999 On thread : tight closing the bolt

   I found that out the hard way mate but its great to have it confirmed I was necking up to 30 cal after that then back down to 7mm but it wasnt enough only about 3 out of 30 blew primers but...

   Liked On: 21-08-2023, 08:48 PM

6. 
   rewa liked post by Bill999 On thread : tight closing the bolt

   I found quite a few problems making brass out of 270/30-06 to fit my 280 rem one even blew the plastic bolt shroud off my tikkas bolt now I just buy the proper headstamped stuff almost put me...

   Liked On: 21-08-2023, 08:42 PM

7. 
   rewa liked post by Bill999 On thread : tight closing the bolt

   could be too long case lenght and needing a trim could be the decapping ball pulling the shoulder forward a bit on the up stroke (too much friction and needs a bit of lube) could be that the...

   Liked On: 21-08-2023, 08:38 PM

8. 
   rugerman liked post by Bill999 On thread : Ruger 10/22 wont cycle

   I did the same as you when getting mine a few years back and luckily it ran on subs like a dream right from day one Id be wearing it in with a few boxes of supers and then checking back to see if...

   Liked On: 21-08-2023, 09:15 AM

9. 
   Micky Duck liked post by Bill999 On thread : Varmint 308 loads

   might even have a chance of expansion if they are lightly built varmit bullets used on larger game too probably not tho most of my recovered normal bullets look like you could use them again

   Liked On: 16-08-2023, 06:12 PM

10. 
    Micky Duck liked post by Bill999 On thread : Show us your DIY gunsmithing jobs

    Mid way pre tidy up of my absolute bubbfication of a Dpt chassis buttstock. I fitted a limbsaver off the original stock that required flattening the end of the what was absent recoil pad, fitted a...

    Liked On: 13-08-2023, 09:03 PM

11. 
    STC liked post by Bill999 On thread : Barrel on Tikka Bush Hunter?

    Trailboss My data isn’t clear enough in my reloading book to repeat Start at 8gr work down Make sure to crimp Sent from my iPad using Tapatalk

    Liked On: 11-08-2023, 08:03 AM

12. 
    40mm liked post by Bill999 On thread : BRNO 600 Question

    my first rifle was a brno 601 in 308 and they are great rifles big fan of the action and the stocks basically mirror the sako 75

    Liked On: 10-08-2023, 12:40 PM

13. 
    Southerner223 liked post by Bill999 On thread : Barrel on Tikka Bush Hunter?

    the standard tikka barrels work fine for roberts 151gr cast bullets at subsonic speeds

    Liked On: 10-08-2023, 11:59 AM

14. 
    Maca49 liked post by Bill999 On thread : recommendations for Goat Rifle

    its just a bolt action that takes ar mags

    Liked On: 09-08-2023, 10:15 AM

15. 
    7mm tragic liked post by Bill999 On thread : Hunting rifle

    A 708 pushing 154sst is what I’m running for what you are looking at Iv stepped down from 7rm to 280rem to now 708 Avoid magnums unless you need them, they are long loud and kick hard. The bullets...

    Liked On: 30-07-2023, 09:54 PM

Page 8 of 121 First 1234567891011121314151617181920212258108 ... Last

• Jump to page: