bluecod1967
Member

58 Likes

Page 3 of 4 First 1234 Last

• Jump to page:

1. 
   bluecod1967 liked post by No.3 On thread : size die scratching cases bush fix

   Sometimes you can end up with a super hard bit of grit in the die wall, giving them a clean and wiping a cotton ball around inside the die might show where it is if it catches a bit of fluff...

   Liked On: 19-09-2023, 01:38 PM

2. 
   bluecod1967 liked post by Jhon On thread : 44 mag powder coated lead accuracy @ $0.31 per projectile

   24gn of Belmont Magnum Pistol Powder which is W296 repackaged. This is published max load for 240gn Hdy Jacketed HP. 20in barrel delivering average of 1750fps, Rossi Puma 92. Recoil is moderate (cf...

   Liked On: 15-09-2023, 10:01 AM

3. 
   bluecod1967 liked post by zimmer On thread : 22 hornet load worked a treat

   I think the smaller flash hole is a plus but the S&B just weren't as good as the WW SX plus I have a lot of the Win cases.

   Liked On: 14-09-2023, 12:44 PM

4. 
   bluecod1967 liked post by zimmer On thread : 22 hornet load worked a treat

   My Savage 32/20 wouldn't perform with cast boolits. I tried several weights and several brands including factory Starline. Barrel is VG+. Swapped to 100gr Hdy XTP HP and got excellent results at 50...

   Liked On: 14-09-2023, 09:00 AM

5. 
   bluecod1967 liked post by zimmer On thread : 22 hornet load worked a treat

   S&B Hornet cases have a smaller flash hole than WW or RP. That is the problem. Standard Hornet dies de-capping pins jam in the S&B flash holes. I found that some de-capped OK, just, whilst others the...

   Liked On: 14-09-2023, 09:00 AM

6. 
   bluecod1967 liked post by Jhon On thread : 22 hornet load worked a treat

   I have a 23D also with a great bore. I bought a bunch of components from a guy who had sold his rifle. He had mostly used S&B brass and ran into pressure and chambering problems with Lil'gun with...

   Liked On: 13-09-2023, 03:12 PM

7. 
   bluecod1967 liked post by Marton On thread : 22 hornet load worked a treat

   I use Lil’gun for my 218 Bee. Similar load as your Hornet, 12.5gn with a SP primer. I mainly use 40gn V-Max projectiles. Lil’gun is a bit fine and it can leak through the side of my Lee powder...

   Liked On: 12-09-2023, 11:11 PM

8. 
   bluecod1967 liked post by zimmer On thread : 22 hornet load worked a treat

   Nice grouping. Always satisfying to get a good result out of a Hornet. I've got 2 Savage Model 23 rifles. One in 22rf and one in 32/20. I just missed a 25/20 (23B) in an auction a few years back....

   Liked On: 12-09-2023, 07:58 PM

9. 
   bluecod1967 liked post by bumblefoot On thread : Mr Lee himself using his Lee Loader

   Mr Lee himself, taking 40sec to make a bullet with his Lee Loader. Here ya go Micky Duck :) The mighty whackamole..... https://www.youtube.com/watch?v=UeEl9wZyabc

   Liked On: 12-09-2023, 06:59 PM

10. 
    bluecod1967 liked post by Tahr On thread : 22 hornet load worked a treat

    Thats cool. When I was a lad I used to dream about shooting a deer with a hornet " 'cos "the cullers did" - I likely read an article in the old NZ Outdoors magazine about it. I used to work in...

    Liked On: 12-09-2023, 06:51 PM

11. 
    bluecod1967 liked post by Makros On thread : 44 mag powder coated lead accuracy @ $0.31 per projectile

    1450fps with AR2207 is exactly the speed I'm using the 44-40 at too, large single hole at 50m with tang sights.

    Liked On: 11-09-2023, 09:28 PM

12. 
    bluecod1967 liked post by mudgripz On thread : is a 3-9x40 scope an overkill for a .22?

    3-9x40 ideal for a hunting 22LR. We shoot bunnies by tens of thousands down here in Cantab and in this high volume situation our gear - rifles and scopes etc - is tested to the maximum. With...

    Liked On: 09-09-2023, 10:58 PM

13. 
    bluecod1967 liked post by JohnDuxbury On thread : iron sights and bad eyesight

    The trouble with eyesight, is that when you get older, its the front bead that is gets fuzzy and unfocused, while the target is fine. And you cant hit anything with that situation. (The solution is...

    Liked On: 09-09-2023, 08:44 PM

14. 
    bluecod1967 liked post by gundoc On thread : papper patch question

    The nitrated paper cartridge is just a neat and tidy way of doing it. Dropping a correct size lubricated bullet into the leed and filling it up with 2F will work fine. I need to make a mould for my...

    Liked On: 25-07-2023, 01:45 PM

15. 
    bluecod1967 liked post by Micky Duck On thread : Making case lube

    I use the graphite powder in a jar lid with some steel shot..dip neck in and they come out coated nicely.

    Liked On: 21-07-2023, 10:27 PM

Page 3 of 4 First 1234 Last

• Jump to page: