bluecod1967
Member

47 Likes

Page 1 of 4 1234 Last

• Jump to page:

1. 
   bluecod1967 liked post by Makros On thread : Safest Method Of Discharging Unknown Primers?

   Water won't deactivate modern primers. They're surprisingly hard to kill.

   Liked On: 30-03-2024, 09:04 AM

2. 
   bluecod1967 liked post by Hunter_Nick On thread : Advice about an 1892 Winchester

   Brilliant, thanks for all the info. That all makes sense to me. I’ll slug the bore and start piecing it together from there. I’ll be sure to be in touch at some point! There are a number of black...

   Liked On: 27-03-2024, 08:29 PM

3. 
   bluecod1967 liked post by rupert On thread : 7x57 case from 270 has anyone tried

   Australia is a completely different market to NZ, even though it is just across the ditch. NZ is called a monopoly. You would be very lucky to see any 7x57R brass in NZ. There was some Norma a few...

   Liked On: 19-03-2024, 08:20 PM

4. 
   bluecod1967 liked post by -BW- On thread : 7x57 case from 270 has anyone tried

   Yes you can make 7x57 from .270, fireforming loads not necessary if you don't want to. I've formed 6mm Rem, 7x57, 8x60, 7x60 from from .30-06 & .270 (and .35 Whelen just to see if I could)...

   Liked On: 19-03-2024, 08:19 PM

5. 
   bluecod1967 liked post by Jhon On thread : 7x57 case from 270 has anyone tried

   Sheesh!

   Liked On: 18-03-2024, 07:49 PM

6. 
   bluecod1967 liked post by shananah On thread : 7x57 case from 270 has anyone tried

   I did some 257 Robts case from .270 cases years ago, found I had to neck ream them as there was quite a bit of thickening at the base of the neck where the .270 shoulder was swaged into the .257...

   Liked On: 17-03-2024, 08:53 PM

7. 
   bluecod1967 liked post by gundoc On thread : bsa sportsman ten feeding issue

   Sometimes rubbish gets trapped in the stock recess below the cartridge lifter. Take the stock off and check, cleaning as required. If you can see marks in the woodwork where the lifter sits when the...

   Liked On: 09-03-2024, 08:28 PM

8. 
   bluecod1967 liked post by Tentman On thread : bsa sportsman ten feeding issue

   I've got my Dad's one of these (originally a Sportsman 15) , he got it about 1955, I started using it about 1969. It's shot thousands each of rabbits and goats, plenty of pigs, possums, quail, cats...

   Liked On: 09-03-2024, 08:28 PM

9. 
   bluecod1967 liked post by Fee Knicks On thread : bsa sportsman ten feeding issue

   New guy here - so take this with a grain of salt .... Give it a good clean with Brakekleen and compressed air . Then report back.

   Liked On: 09-03-2024, 08:28 PM

10. 
    bluecod1967 liked post by MarkN On thread : flounders on a rod anyone ?

    I just watched a fair few of his vids, and not only has he got it dialled in, but his lure choice seems to be, pretty much all the different, smaller kinds that Temu and Ali Express want me to buy,...

    Liked On: 08-11-2023, 04:45 PM

11. 
    bluecod1967 liked post by RV1 On thread : flounders on a rod anyone ?

    Yea, that's the one. Seems to have it dialled in.

    Liked On: 06-11-2023, 06:35 AM

12. 
    bluecod1967 liked post by MB On thread : flounders on a rod anyone ?

    I'm trying, but failing. This is THE guy, he is based in Whangarei: https://www.youtube.com/@AlbertFishOn/videos

    Liked On: 06-11-2023, 06:34 AM

13. 
    bluecod1967 liked post by Shearer On thread : flounders on a rod anyone ?

    236923

    Liked On: 05-11-2023, 07:08 PM

14. 
    bluecod1967 liked post by RV1 On thread : flounders on a rod anyone ?

    I've targeted them with fly and softbait, sight fishing the edges at incoming tide and always spooked them. The only I've caught was with a zed lure while salmon fishing... Dragged zeddy up over the...

    Liked On: 05-11-2023, 02:56 PM

15. 
    bluecod1967 liked post by Micky Duck On thread : flounders on a rod anyone ?

    Ive read a punctured can of sweetcorn..on string so can retrieve it and take home afterwards...works as burley for them... never managed them on rod,speared a few,netted a few and have even gone so...

    Liked On: 05-11-2023, 02:55 PM

Page 1 of 4 1234 Last

• Jump to page: