Bowhunta
Member

30 Likes

Page 1 of 2 12 Last

• Jump to page:

1. 
   Bowhunta liked post by Kelton On thread : Is the new 7mm PRC a lemon ?

   26 or 2217 would be my picks adi powders are more temp stable slightly slower but cheaper and more available animals won’t no the difference and it’s only a few more clicks at the end of the day I...

   Liked On: 09-04-2024, 09:19 PM

2. 
   Bowhunta liked post by LJPRMC On thread : Is the new 7mm PRC a lemon ?

   I shoot a 7mm prc ..... this works for me . !75 gr eld-x at 2950 ft/sec , motivated by 68 gr of 2217 or 67.9 of H1000 , any mag primer you like , COL 3.3 in ADG brass , 24 inch barrel , shoots sub...

   Liked On: 09-04-2024, 09:19 PM

3. 
   Bowhunta liked post by chainsaw On thread : Is the new 7mm PRC a lemon ?

   Yep, you’re bang on RL26 will get you an extra 50 - 150 fps in many calibres. That’s been my experience with 284, 7SAUM & 7RM. The Hornady marketing hype is all focused on their new PRC cartridges……...

   Liked On: 09-04-2024, 03:57 PM

4. 
   Bowhunta liked post by LJPRMC On thread : Is the new 7mm PRC a lemon ?

   Have to agree with you. i even wrote to hornady and told them of the overpressure , and stiff bolt lifts . Their response was " oh really " ..... then i noticed other forums with people saying the...

   Liked On: 09-04-2024, 03:53 PM

5. 
   Bowhunta liked post by PerazziSC3 On thread : Is the new 7mm PRC a lemon ?

   My 22” shoots 195s at about 2850 not sure about factory ammo

   Liked On: 09-04-2024, 03:49 PM

6. 
   Bowhunta liked post by Kelton On thread : Gun Porn, show off your new toys

   Hardly “gunporn” no one’s into porn with uglys but it is new, I’m undecided if it’s going to be a lightish weight hunter in which case il get a z5 for it and keep the carbon stock or flick the...

   Liked On: 07-04-2024, 12:49 AM

7. 
   Bowhunta liked post by garyp On thread : Sako 75 hunter ‘recoil pad replacement’ help

   I have had all sorts of problems with Limbsavers. If any cleaning solvents get on them they will go all mushy and sticky. If you do fit a Limbsaver I suggest you store the rifle barrel down

   Liked On: 28-03-2024, 10:37 PM

8. 
   Bowhunta liked post by flock On thread : Sako 75 hunter ‘recoil pad replacement’ help

   Can't remember, think I just went by measurements, using verniers, just looked think it was this one from GC 246835

   Liked On: 28-03-2024, 10:37 PM

9. 
   Bowhunta liked post by flock On thread : Sako 75 hunter ‘recoil pad replacement’ help

   Mine is a Sako 85 brought 2012, couldn't find any fixing screws so was removed with a stanley knife as clean as I could, it is an awkward thing to do as it was stuck to stay there, the butt pad was...

   Liked On: 28-03-2024, 06:52 PM

10. 
    Bowhunta liked post by flock On thread : Sako 75 hunter ‘recoil pad replacement’ help

    I cut mine back with a drop saw to keep the length overall the same, then screwed in the limbsaver, pefect fit. The trick is to follow the exact angle of the stock, tape it & scribe around the where...

    Liked On: 28-03-2024, 03:15 PM

11. 
    Bowhunta liked post by garyp On thread : Sako 75 hunter ‘recoil pad replacement’ help

    I am in Napier and fit many recoil pads each year. I always use Pachmayr pads which I can supply. The small size almost fit perfectly and look really classy. PM me if interested and I can help you.

    Liked On: 28-03-2024, 03:11 PM

12. 
    Bowhunta liked post by Husky1600#2 On thread : Sako 75 hunter ‘recoil pad replacement’ help

    Easiest way to remove glued on butt pads is to carefully cut them off with a table saw or band saw, cutting through the black stuff after removing any screws. Then finish the end of the butt off on a...

    Liked On: 28-03-2024, 03:11 PM

13. 
    Bowhunta liked post by iambatman On thread : Barrel length considerations

    The lack of full power factory ammo was the major factor. I spent a lot of time considering the .243. In the end I was convinced by Nathan Foster's observations that there are no prizes for...

    Liked On: 18-02-2024, 09:14 AM

14. 
    Bowhunta liked post by tibo On thread : 7mm PRC Factory Hornady ammo issue

    shit I love the ADG brass.... all the Hornady went in the dump

    Liked On: 06-11-2023, 01:08 PM

15. 
    Bowhunta liked post by tibo On thread : 7mm PRC Factory Hornady ammo issue

    Also started load development, the brass that were ok behaved well. Promising result with H4831sc

    Liked On: 06-11-2023, 11:45 AM

Page 1 of 2 12 Last

• Jump to page: