Be very careful not to over tighten the action screws on a Tikka with the standard synthetic stock or you risk deforming the stock and buggering up the free floating lug system which is what gives...
Liked On: 04-05-2024, 09:31 PM
Be very careful not to over tighten the action screws on a Tikka with the standard synthetic stock or you risk deforming the stock and buggering up the free floating lug system which is what gives...
Liked On: 04-05-2024, 11:13 AM
RL26 is a different beast to RL25 in terms of velocity potential, it’s not “bad” but expect to loose 50-70 fps in my experience. The temp sensitivity risk is overstated I believe given NZ...
Liked On: 04-05-2024, 03:24 AM
RL26 is a different beast to RL25 in terms of velocity potential, it’s not “bad” but expect to loose 50-70 fps in my experience. The temp sensitivity risk is overstated I believe given NZ...
Liked On: 03-05-2024, 10:19 PM
RL26 is a different beast to RL25 in terms of velocity potential, it’s not “bad” but expect to loose 50-70 fps in my experience. The temp sensitivity risk is overstated I believe given NZ...
Liked On: 03-05-2024, 08:18 PM
Be very careful not to over tighten the action screws on a Tikka with the standard synthetic stock or you risk deforming the stock and buggering up the free floating lug system which is what gives...
Liked On: 03-05-2024, 06:28 PM
Have used plenty of FC brass over the years & in a heap of different calibres and had good results. Only time I’ve seen something similar was “once fired old brass” (243), probably stored 7-8years or...
Liked On: 27-04-2024, 08:48 AM
Remember that stock design & fit as well as all up weight can play a big part in felt recoil. This becomes more important when you push the weight towards “ultra light” end of the spectrum. This...
Liked On: 26-04-2024, 08:48 AM
Making my 3rd Paulownia/CF stock. This one for my REM M7 260. Close to finished now, another fine sand & final thin coat of epoxy to go. Weighing in at ~660gm including the limbsaver recoil pad....
Liked On: 21-04-2024, 10:52 PM
Making my 3rd Paulownia/CF stock. This one for my REM M7 260. Close to finished now, another fine sand & final thin coat of epoxy to go. Weighing in at ~660gm including the limbsaver recoil pad....
Liked On: 20-04-2024, 09:12 PM
Making my 3rd Paulownia/CF stock. This one for my REM M7 260. Close to finished now, another fine sand & final thin coat of epoxy to go. Weighing in at ~660gm including the limbsaver recoil pad....
Liked On: 20-04-2024, 07:42 PM
Making my 3rd Paulownia/CF stock. This one for my REM M7 260. Close to finished now, another fine sand & final thin coat of epoxy to go. Weighing in at ~660gm including the limbsaver recoil pad....
Liked On: 20-04-2024, 06:33 PM
Making my 3rd Paulownia/CF stock. This one for my REM M7 260. Close to finished now, another fine sand & final thin coat of epoxy to go. Weighing in at ~660gm including the limbsaver recoil pad....
Liked On: 20-04-2024, 05:37 PM
Making my 3rd Paulownia/CF stock. This one for my REM M7 260. Close to finished now, another fine sand & final thin coat of epoxy to go. Weighing in at ~660gm including the limbsaver recoil pad....
Liked On: 20-04-2024, 04:55 PM
Making my 3rd Paulownia/CF stock. This one for my REM M7 260. Close to finished now, another fine sand & final thin coat of epoxy to go. Weighing in at ~660gm including the limbsaver recoil pad....
Liked On: 20-04-2024, 03:14 PM