csmiffy
Member

1987 Likes

Page 37 of 133 First ... 232425262728293031323334353637383940414243444546474849505187 ... Last

• Jump to page:

1. 
   Micky Duck liked post by csmiffy On thread : Greener GP block problems

   Doesn't help but the first time I pulled my A5 apart with no drawings or instructions I might add, was a debacle. Had a shit of a time getting it back together. Whatever I was thinking wasn't...

   Liked On: 23-05-2023, 08:12 PM

2. 
   timattalon liked post by csmiffy On thread : 303 vs 12ga slugs

   The days are gone where you could get a cheap reasonable 303 and ammo to go with it. Bog stock 303 winny powerpoint is up over 60 bucks a packet and probably more. Nothing wrong with it but you will...

   Liked On: 20-05-2023, 12:38 AM

3. 
   pennyless liked post by csmiffy On thread : 303 vs 12ga slugs

   The days are gone where you could get a cheap reasonable 303 and ammo to go with it. Bog stock 303 winny powerpoint is up over 60 bucks a packet and probably more. Nothing wrong with it but you will...

   Liked On: 19-05-2023, 10:00 PM

4. 
   Micky Duck liked post by csmiffy On thread : 303 vs 12ga slugs

   The days are gone where you could get a cheap reasonable 303 and ammo to go with it. Bog stock 303 winny powerpoint is up over 60 bucks a packet and probably more. Nothing wrong with it but you will...

   Liked On: 19-05-2023, 09:34 PM

5. 
   Shanon liked post by csmiffy On thread : Butcher by trade

   And as an aside to back up what you mentioned earlier, I know a younger supervisor there who reckoned the new sharpener would be a good thing. He said he was shit house at keeping his knife sharp on...

   Liked On: 17-05-2023, 11:57 PM

6. 
   Kestrel liked post by csmiffy On thread : Recommended Bergara Gunsmith?

   Bolt should hit up against the barrel if that's what you mean. There should also be a either a hardened steel or a synthetic recoil pin at the rear. That bit is #6 on the drawing

   Liked On: 17-05-2023, 11:18 PM

7. 
   Kestrel liked post by csmiffy On thread : Recommended Bergara Gunsmith?

   Almost sounds like the c clip is loose. Should be as tight as to get on

   Liked On: 17-05-2023, 02:26 PM

8. 
   rugerman liked post by csmiffy On thread : Butcher by trade

   They have just installed about 650k with of machine in my local works. Nudging 800+ installed Robotic arm. Can sharpen 200 knives in a couple of hours. They won't be giving everyone personal knives...

   Liked On: 17-05-2023, 12:01 PM

9. 
   Eat Meater liked post by csmiffy On thread : Butcher by trade

   They have just installed about 650k with of machine in my local works. Nudging 800+ installed Robotic arm. Can sharpen 200 knives in a couple of hours. They won't be giving everyone personal knives...

   Liked On: 17-05-2023, 11:49 AM

10. 
    Shanon liked post by csmiffy On thread : Butcher by trade

    They have just installed about 650k with of machine in my local works. Nudging 800+ installed Robotic arm. Can sharpen 200 knives in a couple of hours. They won't be giving everyone personal knives...

    Liked On: 16-05-2023, 08:17 PM

11. 
    Micky Duck liked post by csmiffy On thread : Butcher by trade

    They have just installed about 650k with of machine in my local works. Nudging 800+ installed Robotic arm. Can sharpen 200 knives in a couple of hours. They won't be giving everyone personal knives...

    Liked On: 16-05-2023, 06:27 PM

12. 
    Beaker liked post by csmiffy On thread : Galvanising suggestions?

    Then spray again. Minimum 2 coats, then give it another. Then get the zinc top coat which is shiny and give it at least one coat with that. Did some handrails years go for a dude and that was...

    Liked On: 16-05-2023, 01:59 PM

13. 
    Bol Tackshin liked post by csmiffy On thread : Unfortunate start to the duck hunting season

    Stay strong mate. I would be filled with so much rage if that happened and not being able to do anything would screw me up

    Liked On: 14-05-2023, 09:34 AM

14. 
    timattalon liked post by csmiffy On thread : Galvanising suggestions?

    Then spray again. Minimum 2 coats, then give it another. Then get the zinc top coat which is shiny and give it at least one coat with that. Did some handrails years go for a dude and that was...

    Liked On: 13-05-2023, 02:05 PM

15. 
    Russian 22. liked post by csmiffy On thread : Galvanising suggestions?

    Then spray again. Minimum 2 coats, then give it another. Then get the zinc top coat which is shiny and give it at least one coat with that. Did some handrails years go for a dude and that was...

    Liked On: 12-05-2023, 10:03 PM

Page 37 of 133 First ... 232425262728293031323334353637383940414243444546474849505187 ... Last

• Jump to page: