csmiffy
Member

3169 Likes

Page 64 of 212 First ... 145051525354555657585960616263646566676869707172737475767778114164 ... Last

• Jump to page:

1. 
   csmiffy liked post by Gibo On thread : Wool or bamboo socks

   Wool all the way!

   Liked On: 02-06-2022, 10:44 AM

2. 
   csmiffy liked post by Tahr On thread : Wool or bamboo socks

   When I was young Mum used to cut the bottom out of her old stockings to put over our gumboot socks to make them last longer. I did it right through my meat hunting years. Funny the things we do...

   Liked On: 02-06-2022, 10:44 AM

3. 
   csmiffy liked post by yeah_na_missed On thread : Wool or bamboo socks

   Brian and Hunteast beat me to it. Their seconds shop is awesome if you're passing through Ashvegas. They make stuff for Swazi and Kiui... keui... kuioo... the fancy yank one with lots of vowels. Very...

   Liked On: 02-06-2022, 07:45 AM

4. 
   csmiffy liked post by Brian On thread : Wool or bamboo socks

   Ashburton sock factory has good wool socks.

   Liked On: 02-06-2022, 07:45 AM

5. 
   csmiffy liked post by Bol Tackshin On thread : Wool or bamboo socks

   Kathmandu merino socks are a bit pricey but last very well and are comfortable. Icebreaker is half price at Torpedo 7 at the moment....

   Liked On: 02-06-2022, 07:44 AM

6. 
   csmiffy liked post by 2post On thread : Wool or bamboo socks

   https://youtu.be/leLwsPyp95k Doubt there’s any bamboo in any of the bamboo products.

   Liked On: 02-06-2022, 07:44 AM

7. 
   csmiffy liked post by MB On thread : Wool or bamboo socks

   Believe it or not, Kmart bamboo stuff is actually OK.

   Liked On: 01-06-2022, 08:21 PM

8. 
   csmiffy liked post by ROKTOY On thread : Hand me down Model 70

   Tea done and a movie on the go, we both set to with the supplied anti rust wipes, going over all treated areas removing the last of the oxide build up and cleaning up the bluing. While I started re...

   Liked On: 26-05-2022, 06:36 PM

9. 
   csmiffy liked post by Scout On thread : Resurgence of interest in the old "Three Oh"?

   Yes I use a few of those in the real old Speeders that were regulated for the 215gr slug, but I haven't been shooting any game with them in the 303, lots in the 30/06 back in the day . Grandpamac...

   Liked On: 24-05-2022, 07:20 PM

10. 
    csmiffy liked post by longshot On thread : Red Dot Sights

    https://www.trademe.co.nz/a/marketplace/sports/hunting-shooting/scopes-sights-mounts/scopes-fixed-power/listing/3603521241

    Liked On: 24-05-2022, 10:31 AM

11. 
    csmiffy liked post by Tahr On thread : The sooper dooper pig 300wsm project thread

    Sometimes cases are hard to get into the shell holder if the swipes or ejector marks are raised. I rub them lightly on some fine emery paper.

    Liked On: 23-05-2022, 06:02 PM

12. 
    csmiffy liked post by ROKTOY On thread : Hand me down Model 70

    What a way to fill in a day. SixtyTen you almost had my day pegged. So many pairs of gloves later. Sand, apply solvent, clean, sand, wire wool, clean, repeat. Split the bolt in two, and gave...

    Liked On: 23-05-2022, 11:05 AM

13. 
    csmiffy liked post by grandpamac On thread : 416 rem mag case trimmer

    There is an answer to your problem but I don't think you are going to like it. Any of the lathe type trimmers should have the length required for the .416. My 50 year old Bair unit does. As far as...

    Liked On: 23-05-2022, 10:40 AM

14. 
    csmiffy liked post by ROKTOY On thread : Hand me down Model 70

    This one is 1976, according to https://www.winchesterguns.com/content/dam/winchester-repeating-arms/support/faq/serial-number-reference/winchester-firearm-manufacture-dates.pdf

    Liked On: 22-05-2022, 03:34 PM

15. 
    csmiffy liked post by PerazziSC3 On thread : 416 rem mag case trimmer

    Side track but these are pretty good buying https://www.guncity.com/federal-416-rem-magnum-safari-400gr-polymer-tip-20-rounds-380468

    Liked On: 22-05-2022, 03:21 PM

Page 64 of 212 First ... 145051525354555657585960616263646566676869707172737475767778114164 ... Last

• Jump to page: