csmiffy
Member

3160 Likes

Page 210 of 211 First ... 110160196197198199200201202203204205206207208209210211 Last

• Jump to page:

1. 
   csmiffy liked post by Paddy79 On thread : Gun Porn, show off your new toys

   New 85 Bavarian in 7mm rem mag83933

   Liked On: 09-03-2018, 05:49 PM

2. 
   csmiffy liked post by viper On thread : Which lever / semi / pump rifle, and why?

   Ohhhh, just had another thought reading the post again. Ruger are doing the 450 bushmaster round and rifle. Bolt action, built in muzzle brake, built in picainny rail for scope mounting, I think H&F...

   Liked On: 08-03-2018, 07:21 PM

3. 
   csmiffy liked post by Walker On thread : Custom build ideas

   I've been down this road a number of times in the past and the only advice I can offer is use a standard off the shelf caliber that you can get in any town like 7mm rem mag, use a good standard...

   Liked On: 07-03-2018, 05:15 PM

4. 
   csmiffy liked post by Walker On thread : parker hale safari project

   Mauser is only mauser, 1.10inch x 12tpi 55degree thread for the parker hales from memory. Neither metric or imperial but a cross over.

   Liked On: 07-03-2018, 05:14 PM

5. 
   csmiffy liked post by Marty Henry On thread : What to do

   Dont ream it roll crimp 2 3/4. I have a similar gun, not nitro proofed like yours, I cut the crimp off 2 3/4s load through a mec and roll crimp. I run 50 or so through the press than card over and...

   Liked On: 05-03-2018, 07:27 PM

6. 
   csmiffy liked post by Tentman On thread : Custom build ideas

   Hello - Over the years I've commissioned a few customs of the blued steel and walnut variety, never spending quite as much as you propose though (in one go). Things to think about with the...

   Liked On: 04-03-2018, 04:16 PM

7. 
   csmiffy liked post by BSA270 On thread : Advice on keeping flip-up scope caps on

   Yep. Strip of rubber car tube works a treat. Been using it forever. Make sure lens are clean and dry. Stretch it over. To remove in a hurry grab it half way along it's length and a bit of upward pull...

   Liked On: 22-02-2018, 09:21 AM

8. 
   csmiffy liked post by Pauli On thread : Walnut and blued steel,

   Nothing fancy csmiffy just the Birchwood Casey walnut stain, 2 maybe 3 coats.

   Liked On: 15-02-2018, 09:16 PM

9. 
   csmiffy liked post by jakewire On thread : Remington in a Spot of Bother

   I am quoting Stug again, however I think he is correct I have a 1990 made rem BDL 30 06 that will , every time, print less than a 1 " group with Winchester 150gr ammo My Mountain rifle which I...

   Liked On: 10-02-2018, 02:00 PM

10. 
    csmiffy liked post by Tentman On thread : Real gunsmiths

    Woody - Your experiences highlight a common issue, most folks have a fair idea of what is "fair value" when they deal with repairs to their car or house because of wide exposure and common knowledge....

    Liked On: 09-02-2018, 05:30 PM

11. 
    csmiffy liked post by Marty Henry On thread : commercial reloaders in christchurch

    They really are a great bit of kit ive got a 45/70, 30/30 and 308 still use them despite having "proper" dies they are so quick for a few rounds.

    Liked On: 08-02-2018, 08:10 PM

12. 
    csmiffy liked post by GMH72 On thread : Left Hand Shooters

    I am right handed but left eye dominant so shoot left handed. Haven't shot a left hand rifle before but don't have an issue with my right handed one.

    Liked On: 07-02-2018, 08:03 PM

13. 
    csmiffy liked post by veitnamcam On thread : Stingers and old Toz rifles

    Pretty sure the old 40gr is the same stuff in new box, the 42gr is an entirely new round and is an emphatic killer for a subsonic round.

    Liked On: 07-02-2018, 07:48 PM

14. 
    csmiffy liked post by StrikerNZ On thread : commercial reloaders in christchurch

    Richard Wilhelm may possibly still offer reloading services..

    Liked On: 06-02-2018, 09:13 PM

15. 
    csmiffy liked post by Tentman On thread : Real gunsmiths

    Great Idea for a thread - I suspect a good deal of being called "a real gunsmith" is choosing your customers, or another way of putting it, only taking on jobs where you can meet the customers...

    Liked On: 06-02-2018, 09:13 PM

Page 210 of 211 First ... 110160196197198199200201202203204205206207208209210211 Last

• Jump to page: