dantheman
Member

38 Likes

Page 2 of 3 First 123 Last

• Jump to page:

1. 
   dantheman liked post by makka On thread : Someone's old project Mauser

   I like that

   Liked On: 05-08-2024, 09:18 PM

2. 
   dantheman liked post by Micky Duck On thread : Someone's old project Mauser

   I would hunt with that. Hope it shoots well for you, definitely something different.will need ear protection,that is for sure.

   Liked On: 05-08-2024, 09:18 PM

3. 
   dantheman liked post by csmiffy On thread : Someone's old project Mauser

   They were a neat little rifle. Had a shot out of one back about 86-87. Had a saddle ring. It was a 308. Always meant to get one but never did.

   Liked On: 05-08-2024, 09:18 PM

4. 
   dantheman liked post by bumblefoot On thread : Old school hunting

   I saw this pic on the FB NZ deer cullers page; and for some reason just love it.... Using the great 7.7 Rimmed Creedmoor of course! ;) 243386

   Liked On: 10-02-2024, 09:28 AM

5. 
   dantheman liked post by NewbieZAR On thread : Adapting rimfire suppressor for .38 special...

   check out the sonic feather weight supressor, a mate has one on his 357 mag citadel lever gun and still uses the factory iron sights

   Liked On: 07-12-2023, 04:41 PM

6. 
   dantheman liked post by AR7 On thread : Adapting rimfire suppressor for .38 special...

   238452 Hi Dantherman my 38 special is 38 mm od and 210mm long originally had it drilled out @ 10mm but increased the exit hole to 10.5 including a couple of baffles in then down to...

   Liked On: 03-12-2023, 06:33 PM

7. 
   dantheman liked post by AR7 On thread : Adapting rimfire suppressor for .38 special...

   238500238500 test of 38 Sp noise level across 300m valley FED 158 grain lead RN V. Very quiet slight sound in flight easy to hear impact in grass /soft dirt Freedom 158 grain copper...

   Liked On: 02-12-2023, 07:39 PM

8. 
   dantheman liked post by AR7 On thread : Adapting rimfire suppressor for .38 special...

   238501 Rossi 38 sp / 357 used in test

   Liked On: 02-12-2023, 07:39 PM

9. 
   dantheman liked post by AR7 On thread : Adapting rimfire suppressor for .38 special...

   Hi I did this conversion but from a 30 cal. centerfire sup worked out really well especially using the 158 grain 38 sp lead Rn [American eagle ]

   Liked On: 30-11-2023, 07:32 PM

10. 
    dantheman liked post by Boner On thread : Filling open grain on stock on the cheap

    Plus 1 for clear epoxy. Then sand right back and oil.

    Liked On: 16-11-2023, 05:15 PM

11. 
    dantheman liked post by gundoc On thread : Filling open grain on stock on the cheap

    Get a bottle of Artists Linseed Oil (Paper Plus, Warehouse Stationery, etc), apply and allow to dry (1-2 days) polish off across the grain with coarse cloth, repeat a couple of times and rub the last...

    Liked On: 11-11-2023, 03:24 PM

12. 
    dantheman liked post by Micky Duck On thread : Filling open grain on stock on the cheap

    the oil,any oil will help.....drying out over the years will have shrunk wit hwood,allowing cracks to open. sounds like your on to it.

    Liked On: 11-11-2023, 03:23 PM

13. 
    dantheman liked post by sportco62 On thread : Filling open grain on stock on the cheap

    At the end of the day - the stock on a military SMLE was never a masterpiece - it was a functional handle for a foot soldier to use to point his rifle away from his mates. The finish was never in the...

    Liked On: 11-11-2023, 03:23 PM

14. 
    dantheman liked post by Marty Henry On thread : Filling open grain on stock on the cheap

    Epoxy, troweled over cracks and pits then smoothed off to the level of the wood also works a treat and doesn't shrink

    Liked On: 11-11-2023, 11:43 AM

15. 
    dantheman liked post by No good names left On thread : Filling open grain on stock on the cheap

    I've used coloured wood filler before, water based so it can be thinned out to get into fine pores. Available in various wood colours as well as some primary colours. Depends where you are I could...

    Liked On: 11-11-2023, 11:43 AM

Page 2 of 3 First 123 Last

• Jump to page: