Delphus
Member

646 Likes

Page 21 of 44 First ... 7891011121314151617181920212223242526272829303132333435 ... Last

• Jump to page:

1. 
   chainsaw liked post by Delphus On thread : Carbon wrap complete

   Ha yep sure is! Many mistakes were made. I’m sure that if I did it again I would do a much better job of it. I made the stock from powlonia :) Yours looks great man!

   Liked On: 10-06-2022, 04:01 PM

2. 
   Moa Hunter liked post by Delphus On thread : Carbon wrap complete

   Well I have finally done it. It’s not pretty in places, but that just gives it a bit of character. I have it sanded down to a 1200 grit paper, and think I’ll leave it there. I could give it the...

   Liked On: 09-06-2022, 11:41 PM

3. 
   Hook_Grass liked post by Delphus On thread : Carbon wrap complete

   Well I have finally done it. It’s not pretty in places, but that just gives it a bit of character. I have it sanded down to a 1200 grit paper, and think I’ll leave it there. I could give it the...

   Liked On: 09-06-2022, 10:38 PM

4. 
   chainsaw liked post by Delphus On thread : Carbon wrap complete

   Well I have finally done it. It’s not pretty in places, but that just gives it a bit of character. I have it sanded down to a 1200 grit paper, and think I’ll leave it there. I could give it the...

   Liked On: 09-06-2022, 10:26 PM

5. 
   Joe_90 liked post by Delphus On thread : Carbon wrap complete

   Well I have finally done it. It’s not pretty in places, but that just gives it a bit of character. I have it sanded down to a 1200 grit paper, and think I’ll leave it there. I could give it the...

   Liked On: 09-06-2022, 09:47 PM

6. 
   Micky Duck liked post by Delphus On thread : Carbon wrap complete

   All up this cost me about $140 in parts. Labour on the other hand……

   Liked On: 09-06-2022, 09:01 PM

7. 
   Micky Duck liked post by Delphus On thread : Carbon wrap complete

   Well I have finally done it. It’s not pretty in places, but that just gives it a bit of character. I have it sanded down to a 1200 grit paper, and think I’ll leave it there. I could give it the...

   Liked On: 09-06-2022, 09:01 PM

8. 
   40mm liked post by Delphus On thread : Carbon wrap complete

   All up this cost me about $140 in parts. Labour on the other hand……

   Liked On: 09-06-2022, 08:57 PM

9. 
   dannyb liked post by Delphus On thread : Carbon wrap complete

   All up this cost me about $140 in parts. Labour on the other hand……

   Liked On: 09-06-2022, 08:56 PM

10. 
    dannyb liked post by Delphus On thread : Carbon wrap complete

    Well I have finally done it. It’s not pretty in places, but that just gives it a bit of character. I have it sanded down to a 1200 grit paper, and think I’ll leave it there. I could give it the...

    Liked On: 09-06-2022, 08:55 PM

11. 
    199p liked post by Delphus On thread : Carbon wrap complete

    Well I have finally done it. It’s not pretty in places, but that just gives it a bit of character. I have it sanded down to a 1200 grit paper, and think I’ll leave it there. I could give it the...

    Liked On: 09-06-2022, 08:46 PM

12. 
    Ryan_Songhurst liked post by Delphus On thread : Carbon wrap complete

    Well I have finally done it. It’s not pretty in places, but that just gives it a bit of character. I have it sanded down to a 1200 grit paper, and think I’ll leave it there. I could give it the...

    Liked On: 09-06-2022, 08:45 PM

13. 
    timattalon liked post by Delphus On thread : Help with parallax

    Did some googling and think I have it sorted :)

    Liked On: 03-06-2022, 04:42 AM

14. 
    Micky Duck liked post by Delphus On thread : Woodworking gurus

    I cut it further back and epoxied a piece of powlonia on there, then shaped it back. Came up mint :) 198104

    Liked On: 31-05-2022, 08:55 PM

15. 
    JessicaChen liked post by Delphus On thread : Gutted.

    I FOUND THEM! In my wisdom I put them up high in the rafters of my garage. I found them yesterday accidentally. I am stoked! I now have to dig up the skull and glue them on :)

    Liked On: 24-05-2022, 10:30 PM

Page 21 of 44 First ... 7891011121314151617181920212223242526272829303132333435 ... Last

• Jump to page: