Dicko
Member

725 Likes

Page 34 of 49 First ... 2021222324252627282930313233343536373839404142434445464748 ... Last

• Jump to page:

1. 
   veitnamcam liked post by Dicko On thread : Hi tec stock failure

   I bought one of Ken’s stocks last month for a new build 06. Mostly due to forum feedback. Been impressed with it so far. Well made and finished, great comb dimensions, and seems to handle the...

   Liked On: 08-03-2021, 01:13 PM

2. 
   JMJW liked post by Dicko On thread : 22 hornet loads

   I shoot a win pre 64 model 70 .22H. I find anywhere between 11 and 13 grains of Lill gun works well, 12-13 is best for me. Projectile choice makes a Hugh difference. 40 gn Nosler or 45 gn Sierra...

   Liked On: 07-03-2021, 10:01 AM

3. 
   Snowgrass liked post by Dicko On thread : Stuck case stuck goodly.

   In my experience with cases stuck in dies, it’s the area in front of the web towards the base that usually binds in the LGS die if you’re light on lube. If you want a very good case lube that is...

   Liked On: 02-03-2021, 06:06 PM

4. 
   flock liked post by Dicko On thread : Stuck case stuck goodly.

   In my experience with cases stuck in dies, it’s the area in front of the web towards the base that usually binds in the LGS die if you’re light on lube. If you want a very good case lube that is...

   Liked On: 02-03-2021, 04:33 PM

5. 
   Husky1600 liked post by Dicko On thread : 22 hornet loads

   I shoot a win pre 64 model 70 .22H. I find anywhere between 11 and 13 grains of Lill gun works well, 12-13 is best for me. Projectile choice makes a Hugh difference. 40 gn Nosler or 45 gn Sierra...

   Liked On: 28-02-2021, 08:37 PM

6. 
   JessicaChen liked post by Dicko On thread : Lightweight portable bone saw

   While you can cut through both, I’m more intrigued as to why you would unless bringing animals out whole. If this is the case, purchase a butchers hand saw. For skull caps in the bush a Silky or a...

   Liked On: 27-02-2021, 03:24 AM

7. 
   dannyb liked post by Dicko On thread : 7mm Rem Mag Recipe

   RL19 at 64, RL22 at 67, RL 25 at 70 grains all give ~2950 to 3000 fps with a 160/162 gn pill if you can find them and will produce accurate loads.

   Liked On: 21-02-2021, 05:58 AM

8. 
   jakewire liked post by Dicko On thread : Fail-safe 30 06 load

   56 to 58 grains gives me 2800 to 2900 fps in a 24 inch tube with a 165 BT without pressure signs in RP brass. Better accuracy in the 56-57 grain range.

   Liked On: 20-02-2021, 08:56 AM

9. 
   jakewire liked post by Dicko On thread : Fail-safe 30 06 load

   Yeah, 56-58 gns of 2209 behind a 165. Brass can matter, hint.

   Liked On: 18-02-2021, 06:40 PM

10. 
    chainsaw liked post by Dicko On thread : Why does pulling case out of FL resizing die require so much force?

    Hornady dies work fine if you lube inside the necks. Saying this, they are my least favourite dies.

    Liked On: 16-02-2021, 12:30 PM

11. 
    tetawa liked post by Dicko On thread : Why does pulling case out of FL resizing die require so much force?

    You need to lube inside the case neck! Otherwise friction of the expander ball will stretch your case. Lots of ways to do this from graphite powder to lube on a swab, patch and tweezers or a ear...

    Liked On: 15-02-2021, 05:10 PM

12. 
    Nathanfish liked post by Dicko On thread : 1-8 power scopes

    In one inch tubes, The little 3-9x36 z3 swaro is worth a look. A bottom end of 3x is ok in the tight stuff. The 2.5-8 and 2-7x leupold’s also. Not quite as bright though to me. In 30 mm the...

    Liked On: 15-02-2021, 12:05 PM

13. 
    57jl liked post by Dicko On thread : Blaser K95

    Gkp, I know you asked about Blasers but if you see a Merkel K3 or 4 they are also well worth looking at. Very similar in design, quality and...

    Liked On: 14-02-2021, 08:52 PM

14. 
    veitnamcam liked post by Dicko On thread : Why does pulling case out of FL resizing die require so much force?

    You need to lube inside the case neck! Otherwise friction of the expander ball will stretch your case. Lots of ways to do this from graphite powder to lube on a swab, patch and tweezers or a ear...

    Liked On: 14-02-2021, 04:46 PM

15. 
    Pushover liked post by Dicko On thread : Why does pulling case out of FL resizing die require so much force?

    You need to lube inside the case neck! Otherwise friction of the expander ball will stretch your case. Lots of ways to do this from graphite powder to lube on a swab, patch and tweezers or a ear...

    Liked On: 14-02-2021, 02:50 PM

Page 34 of 49 First ... 2021222324252627282930313233343536373839404142434445464748 ... Last

• Jump to page: