Driverman
Member

202 Likes

Page 2 of 14 First 1234567891011121314 Last

• Jump to page:

1. 
   T.FOYE liked post by Driverman On thread : Removing 'leading' from shooting cast bullets

   I shoot thousand of cast bullets with zero leading but thats because I powder coat everything. When I didnt powder coat I used to occasionally get a barrel full of lead in 44 mag heavy loads. Removal...

   Liked On: 26-09-2022, 11:01 PM

2. 
   300CALMAN liked post by Driverman On thread : Removing 'leading' from shooting cast bullets

   I shoot thousand of cast bullets with zero leading but thats because I powder coat everything. When I didnt powder coat I used to occasionally get a barrel full of lead in 44 mag heavy loads. Removal...

   Liked On: 26-09-2022, 01:29 PM

3. 
   Moa Hunter liked post by Driverman On thread : Removing 'leading' from shooting cast bullets

   I shoot thousand of cast bullets with zero leading but thats because I powder coat everything. When I didnt powder coat I used to occasionally get a barrel full of lead in 44 mag heavy loads. Removal...

   Liked On: 26-09-2022, 08:04 AM

4. 
   john m liked post by Driverman On thread : UNBURNT POWDER

   Cast Bullet Loads for Military Rifles - Article The following is a very good read with excellent information: CAST BULLET LOADS FOR MILITARY RIFLES BY C.E. Harris Cast bullet loads usually...

   Liked On: 07-07-2022, 08:48 AM

5. 
   Three O'Three liked post by Driverman On thread : UNBURNT POWDER

   Cast Bullet Loads for Military Rifles - Article The following is a very good read with excellent information: CAST BULLET LOADS FOR MILITARY RIFLES BY C.E. Harris Cast bullet loads usually...

   Liked On: 06-07-2022, 11:34 PM

6. 
   rewa liked post by Driverman On thread : First casts

   Your mold is too cold, your alloy is too cold. Your alloy needs some tin and your mold needs a real good clean with a toothbrush and acetone. Then when youve done this look a getting sharply defined...

   Liked On: 16-05-2022, 09:06 PM

7. 
   The bomb liked post by Driverman On thread : First casts

   Your mold is too cold, your alloy is too cold. Your alloy needs some tin and your mold needs a real good clean with a toothbrush and acetone. Then when youve done this look a getting sharply defined...

   Liked On: 24-04-2022, 08:40 AM

8. 
   7mmwsm liked post by Driverman On thread : First casts

   Your mold is too cold, your alloy is too cold. Your alloy needs some tin and your mold needs a real good clean with a toothbrush and acetone. Then when youve done this look a getting sharply defined...

   Liked On: 24-04-2022, 07:14 AM

9. 
   outlander liked post by Driverman On thread : First casts

   Your mold is too cold, your alloy is too cold. Your alloy needs some tin and your mold needs a real good clean with a toothbrush and acetone. Then when youve done this look a getting sharply defined...

   Liked On: 24-04-2022, 01:24 AM

10. 
    Micky Duck liked post by Driverman On thread : First casts

    Your mold is too cold, your alloy is too cold. Your alloy needs some tin and your mold needs a real good clean with a toothbrush and acetone. Then when youve done this look a getting sharply defined...

    Liked On: 23-04-2022, 10:31 PM

11. 
    Bill999 liked post by Driverman On thread : 2,000,000km on the clock

    Ive had 2 Hiace diesel shuttles that did over a million k before I sold them at 10 years old. Original motors. Another running on LPG over a million k. When we pulled it down had 3thou wear in the...

    Liked On: 29-03-2022, 03:29 PM

12. 
    Jhon liked post by Driverman On thread : Casting for an SMLE

    Im watching this thread with interest. Powdercoating is just a term for providing a polymer coating to a projectile The coating is a good deal harder than the lead and if done right will not leave a...

    Liked On: 27-03-2022, 12:44 AM

13. 
    Nugget connaisseur liked post by Driverman On thread : 2,000,000km on the clock

    Ive had 2 Hiace diesel shuttles that did over a million k before I sold them at 10 years old. Original motors. Another running on LPG over a million k. When we pulled it down had 3thou wear in the...

    Liked On: 24-03-2022, 09:54 PM

14. 
    40mm liked post by Driverman On thread : Reasons to be wary of Others reloads

    I use the clamp section of a pipe flaring tool to grip the projectile through the loading press die hole and have disassembled many loaded rounds with ease.

    Liked On: 19-03-2022, 04:11 PM

15. 
    nevereadyfreddy liked post by Driverman On thread : Reasons to be wary of Others reloads

    I use the clamp section of a pipe flaring tool to grip the projectile through the loading press die hole and have disassembled many loaded rounds with ease.

    Liked On: 19-03-2022, 11:32 AM

Page 2 of 14 First 1234567891011121314 Last

• Jump to page: