ebf
Mushroom juice ! Hic !

3737 Likes

Page 156 of 250 First ... 56106142143144145146147148149150151152153154155156157158159160161162163164165166167168169170206 ... Last

• Jump to page:

1. 
   Beaker liked post by ebf On thread : MOA outta whack

   take it to the 100 yard range on a calmish day make sure your 100yd zero is spot on. then shoot a box - 5 moa right, up, left, down. if it is tracking correctly you should end up at the start...

   Liked On: 27-09-2015, 10:31 AM

2. 
   Danny liked post by ebf On thread : MOA outta whack

   delay judgement until you've done some fundamental tests :D i've seen nightforce scopes that shat themselves, anything can break or have a manufacturing fault. having said that, 99.9% of issues...

   Liked On: 27-09-2015, 09:41 AM

3. 
   7mmsaum liked post by ebf On thread : MOA outta whack

   delay judgement until you've done some fundamental tests :D i've seen nightforce scopes that shat themselves, anything can break or have a manufacturing fault. having said that, 99.9% of issues...

   Liked On: 26-09-2015, 08:07 PM

4. 
   Sasquatch liked post by ebf On thread : MOA outta whack

   take it to the 100 yard range on a calmish day make sure your 100yd zero is spot on. then shoot a box - 5 moa right, up, left, down. if it is tracking correctly you should end up at the start...

   Liked On: 26-09-2015, 08:05 PM

5. 
   veitnamcam liked post by ebf On thread : MOA outta whack

   take it to the 100 yard range on a calmish day make sure your 100yd zero is spot on. then shoot a box - 5 moa right, up, left, down. if it is tracking correctly you should end up at the start...

   Liked On: 26-09-2015, 07:02 PM

6. 
   R93 liked post by ebf On thread : MOA outta whack

   take it to the 100 yard range on a calmish day make sure your 100yd zero is spot on. then shoot a box - 5 moa right, up, left, down. if it is tracking correctly you should end up at the start...

   Liked On: 26-09-2015, 06:41 PM

7. 
   mikee liked post by ebf On thread : MOA outta whack

   take it to the 100 yard range on a calmish day make sure your 100yd zero is spot on. then shoot a box - 5 moa right, up, left, down. if it is tracking correctly you should end up at the start...

   Liked On: 26-09-2015, 06:36 PM

8. 
   ZG47 liked post by ebf On thread : Ex-NZ Army Unimogs

   Unimogs are awesome, used to have a mog ambulance in the army... The side angle that thing could handle was just insane :D

   Liked On: 20-09-2015, 09:45 PM

9. 
   Cyclops liked post by ebf On thread : My Introduction to pistol shooting

   Some tips for your first major comp : Concentrate on grip and sight picture (repeat N times) ! Ignore speed for now, build a solid base first and then speed up only enough to not start hurting...

   Liked On: 20-09-2015, 07:38 PM

10. 
    Ruger liked post by ebf On thread : My Introduction to pistol shooting

    Couple of guys in Hamilton found the box surprisingly small :D Yet to see a functioning chrony stage at a comp in NZ... Yeah, my comments were from a shooters point of view. The full story for...

    Liked On: 18-09-2015, 06:49 AM

11. 
    Dan88 liked post by ebf On thread : Lathe & mill projects

    Next was a barrel clamp and action wrench. The barrel clamp was designed so that I could bolt it to the towbar of my van and use it on the range. Some interesting lessons learnt - off-centre work...

    Liked On: 17-09-2015, 10:58 PM

12. 
    Scouser liked post by ebf On thread : Lathe & mill projects

    Next one was to make a second base plate for my SKP buttplate. I wanted the same setup on both my fullbore and rimfire FTR rifles, and figured making a 2nd baseplate would be way cheaper than buying...

    Liked On: 17-09-2015, 09:50 PM

13. 
    Scouser liked post by ebf On thread : Lathe & mill projects

    First up, some simple turning and threading. Had to make a smaller mandrel for the slitting saw, so that I could maximize the depth I could saw to (see barrel clamp later) 40739 The bottom...

    Liked On: 17-09-2015, 09:50 PM

14. 
    Scouser liked post by ebf On thread : Lathe & mill projects

    Earlier this year stumpy discovered that nappies and baby food apparently is a higher priority than a metalwork hobby... :P So after some negotiations with the Mrs (profuse begging and groveling...

    Liked On: 17-09-2015, 09:49 PM

15. 
    res liked post by ebf On thread : Lathe & mill projects

    Earlier this year stumpy discovered that nappies and baby food apparently is a higher priority than a metalwork hobby... :P So after some negotiations with the Mrs (profuse begging and groveling...

    Liked On: 17-09-2015, 08:17 PM

Page 156 of 250 First ... 56106142143144145146147148149150151152153154155156157158159160161162163164165166167168169170206 ... Last

• Jump to page: