Edunn
Member

87 Likes

Page 1 of 6 123456 Last

• Jump to page:

1. 
   Edunn liked post by Filthman On thread : First Hunt - GSP/Lab

   Well done....great when training all comes together.if you think it's good now keep it up and see what happens with your dog at years 5 and 6...like wine ,they improve with age

   Liked On: 01-02-2021, 11:46 AM

2. 
   Edunn liked post by Hunty1 On thread : First Hunt - GSP/Lab

   Shit hot! Cheers for the write up. Looks like some nice otago country. I do miss it!

   Liked On: 01-02-2021, 10:21 AM

3. 
   Edunn liked post by JohnPH On thread : Neck Tension Issue... I think

   I've had a similar problem with both the 7Rem magnums I've owned and loaded for. No problem with w/w brass, but as soon as I started developing loads with Norma brass I started getting a few pressure...

   Liked On: 01-02-2021, 09:58 AM

4. 
   Edunn liked post by Micky Duck On thread : First Hunt - GSP/Lab

   all good ,you are definately on to a good thing with the dog....please keep posting.

   Liked On: 29-01-2021, 11:07 PM

5. 
   Edunn liked post by bunji On thread : First Hunt - GSP/Lab

   Good stuff,love the photo with her & the deer ,she has the "l am going to need a bigger bowl "look . Good luck with the training & future hunts :thumbsup:

   Liked On: 29-01-2021, 11:07 PM

6. 
   Edunn liked post by Tui4Me On thread : Neck Tension Issue... I think

   Usually the expander button on FL sizing die will clean a lot of the neck soot out once it has been pushed in and out again. All you need to do is purchase some dry powdered graphite lube (the...

   Liked On: 29-01-2021, 01:14 PM

7. 
   Edunn liked post by matagouri On thread : Neck Tension Issue... I think

   Do a bit of research on "cold bullet weld". Longrange hunting.com,, should have some good reading on it... Expander mandrels, do some research on them for setting your neck tension.... You can...

   Liked On: 29-01-2021, 10:23 AM

8. 
   Edunn liked post by Marty Henry On thread : Neck Tension Issue... I think

   Not the issue here but it is possible under the right conditions for bullets to "cold solder" themselves to the neck and that does cause pressure. It was first noticed in the 20s with batches of...

   Liked On: 28-01-2021, 05:20 PM

9. 
   Edunn liked post by hebe On thread : First Hunt - GSP/Lab

   Go the GsP/Lab. My one is a bit hypo as well but they slowly grow out of it. Awesome story

   Liked On: 27-01-2021, 02:38 PM

10. 
    Edunn liked post by Sako851 On thread : First Hunt - GSP/Lab

    nice work and looks like your gonna have a great dog there

    Liked On: 27-01-2021, 11:08 AM

11. 
    Edunn liked post by JoshC On thread : First Hunt - GSP/Lab

    Epic man, looks like you've done well with her! The hypo part's probably the GSP...she should grow out of it.

    Liked On: 27-01-2021, 10:55 AM

12. 
    Edunn liked post by Trout On thread : Snorkels (For trucks, not diving)

    When you pick up yr truck with a new snorkel fitted from yr garage.Befor you pay the bill,have yr truck idling,put yr hand over the snorkel air intake opening.if it doesn't just about stall,its not...

    Liked On: 30-06-2020, 04:28 PM

13. 
    Edunn liked post by gadgetman On thread : Snorkels (For trucks, not diving)

    I'm more DIY, just so I know it's sealed. Found them all to be much-of-a-muchness between the cheaper and more expensive. The cheaper one had a great instruction sheet that said to 'Read the...

    Liked On: 30-06-2020, 02:07 PM

14. 
    Edunn liked post by Tertle On thread : Snorkels (For trucks, not diving)

    I can vouch for their products, I installed one myself on a Isuzu trooper a while back, worked a treat, and measure 12 times then cut once! Very unnerving to intentionally cut into parts of your...

    Liked On: 30-06-2020, 02:03 PM

15. 
    Edunn liked post by Hunty1 On thread : Snorkels (For trucks, not diving)

    Went thru this a while back, places in Dunedin that quoted to fit a snorkel where Midway motors and St Kilda Automotive (ironman 4x4 agent). Didn't end up using either as ended upgrading to a truck...

    Liked On: 30-06-2020, 12:45 PM

Page 1 of 6 123456 Last

• Jump to page: