Fssprecision
Member

341 Likes

Page 10 of 23 First 1234567891011121314151617181920212223 Last

• Jump to page:

1. 
   Fssprecision liked post by AR7 On thread : Pistol Barrel Change

   Hey Darren nice work as always . Hope it test fires true :)

   Liked On: 23-09-2023, 01:46 PM

2. 
   Fssprecision liked post by Williamfga On thread : Winchester M70 XTR FWT .308 Build ALL ADVICE WELCOME!!!!!!

   Finally finished, Had Bolt and barrel fluted by Greystone guns and Cerakoted. came out pretty good I think. 233699233700233701233702

   Liked On: 22-09-2023, 07:52 AM

3. 
   Fssprecision liked post by Williamfga On thread : Winchester M70 XTR FWT .308 Build ALL ADVICE WELCOME!!!!!!

   224201224202224203 DPT suppressor, several cotes of boiled linseed. will give it 5 or so more cotes and cerakote all the metal once bank account recovers.

   Liked On: 22-09-2023, 07:50 AM

4. 
   Fssprecision liked post by winchesterM69A On thread : Ultrsonic cleaning solution

   Simple Green , water , heat , and time

   Liked On: 16-09-2023, 04:17 AM

5. 
   Fssprecision liked post by blip On thread : Ptg reamers

   Reamer just turned up. That was pretty fast and drama free...

   Liked On: 13-09-2023, 01:21 PM

6. 
   Fssprecision liked post by AR7 On thread : Finally, Bergara single shot 9mm!!

   Hi All what is the barrel twist rate can you reveal with my experimenting makes a big difference on weight of pills vs good MOA FSS Made one out of a New England Handi break action ...

   Liked On: 11-09-2023, 09:20 AM

7. 
   Fssprecision liked post by blip On thread : Ptg reamers

   been looking into those as well but so far Ive found a way to do it that works surprisingly well.

   Liked On: 05-09-2023, 09:13 AM

8. 
   Fssprecision liked post by Squirrel On thread : Importing a firearm part without an import permit

   Even some years ago you could not apply for a permit retrospectively, the items were seized as they were imported without a permit. Not worth the risk considering there is no fee for a permit at...

   Liked On: 03-09-2023, 11:12 AM

9. 
   Fssprecision liked post by Russian 22. On thread : Importing a firearm part without an import permit

   why would you even bother doing this if you know you are going to buy something from overseas? it's not as though it is a spontaneous decision. My import permit for a bayonet was a breeze. List...

   Liked On: 03-09-2023, 11:12 AM

10. 
    Fssprecision liked post by Pommy On thread : Silencer Thread - which is best???

    Yeah the diameter of the barrel is what matters. From a mechanical perspective, the best thread to use is the fattest one you can use that still gives a good shoulder for the suppressor to tighten up...

    Liked On: 23-08-2023, 03:34 AM

11. 
    Fssprecision liked post by AR7 On thread : Ruger 10/22 wont cycle

    Hi All 12 - 13 inches with supp. on . minus how long is your suppressor ?? hahaa makes a very short barrel !! you must have a long stock to get it legal length . i have...

    Liked On: 22-08-2023, 06:10 PM

12. 
    Fssprecision liked post by Grey Kiwi On thread : Re tension a spring?

    Thanks guys. Yes, I have already ordered a new spring and extractors from Kilwell. As I single load, the extractors both open up at the same time to go over the rim of the case (which I have part...

    Liked On: 20-08-2023, 03:35 PM

13. 
    Fssprecision liked post by gundoc On thread : Adapting rimfire suppressor for .38 special...

    The principal requirement of a suppressor is for it to have enough internal volume to contain and dissipate the gases produced. The gases are proportional to the amount of powder burned. A .38...

    Liked On: 12-08-2023, 04:56 PM

14. 
    Fssprecision liked post by XR500 On thread : Managing recoil for a rookie shooter

    #1. Fit a suppressor. #2. reload. And before all that, go join a club and you will be swamped with assistance for shooting more comfortably and accurately :D

    Liked On: 11-08-2023, 10:14 AM

15. 
    Fssprecision liked post by Happy Jack On thread : Useing the firearms register

    Thanks Fssprecision look out for an email in the next couple of days

    Liked On: 07-08-2023, 08:59 PM

Page 10 of 23 First 1234567891011121314151617181920212223 Last

• Jump to page: