gqhoon
Member

240 Likes

Page 10 of 16 First 12345678910111213141516 Last

• Jump to page:

1. 
   gqhoon liked post by Wingman On thread : Economical Gong Gun cartridge?

   The 6x45 really doesnt have the engine room for heavy projectiles and the light ones suffer on low BCs. Personally Id recomend a 6mmBR or 6mm dasher. I run a dasher with 2208 and 95gr bullets at...

   Liked On: 03-12-2020, 11:48 AM

2. 
   gqhoon liked post by TARGEX On thread : Projectile manufacturing

   Mmm, that Bryn. The same one that is running a logging gang over Summer & does cabinet making & rifle stocks etc over winter as there will never be enough money or quantities required in nz to make a...

   Liked On: 01-12-2020, 08:22 PM

3. 
   gqhoon liked post by veitnamcam On thread : Gun Porn, show off your new toys

   Patience is a virtue so they say and I have certainly been virtuous :D Defiance deviant ultralight fully nitrided with blind bolt release pin in "XM" lenght. Defiance alloy bottom metal and...

   Liked On: 29-11-2020, 07:58 PM

4. 
   gqhoon liked post by Plinky On thread : Glacier Rifle Company - NZ Made Titanium Actions

   151164

   Liked On: 13-10-2020, 06:46 PM

5. 
   gqhoon liked post by Plinky On thread : Glacier Rifle Company - NZ Made Titanium Actions

   151165

   Liked On: 13-10-2020, 06:46 PM

6. 
   gqhoon liked post by Dreamer On thread : Gun Porn, show off your new toys

   Full body photos... This was a long wait in the end. Blaser K95 classic 6.5x55. As soon as I seen they where making the straight butt stock I wanted one but also I wanted something for me to...

   Liked On: 09-10-2020, 08:48 PM

7. 
   gqhoon liked post by Steelisreal On thread : Trying something, Eric Cortina method of load development

   No, that is incorrect. For the purposes of getting started with load testing, 'jam' is the point beyond which a projectile will stick in the rifling and stay behind if a loaded round is removed from...

   Liked On: 06-10-2020, 07:43 AM

8. 
   gqhoon liked post by MGNZ On thread : DIY Induction Annealer

   Much better feed reliability with 260 cases. https://youtu.be/NZUAKkAxfk4

   Liked On: 02-10-2020, 08:53 AM

9. 
   gqhoon liked post by MGNZ On thread : DIY Induction Annealer

   Still have a few feed bugs to work out, but not bad for a first run. https://youtu.be/BujviMWKw0o 150486

   Liked On: 02-10-2020, 08:50 AM

10. 
    gqhoon liked post by MGNZ On thread : DIY Induction Annealer

    Quick update on this project. I'm starting to work on an automatic case feeder design add-on for the annealer. The plan is to 3D print the parts and provide the CAD for others. The feeding mechanism...

    Liked On: 24-09-2020, 10:38 AM

11. 
    gqhoon liked post by Tahr On thread : 2020 SHOT STAGS

    Nice way to finish my wallaby trip this morning. 147910

    Liked On: 02-09-2020, 01:56 PM

12. 
    gqhoon liked post by Tahr On thread : 2020 SHOT STAGS

    Another pic of this weeks buck. 148189

    Liked On: 02-09-2020, 01:55 PM

13. 
    gqhoon liked post by johnd On thread : DIY Induction Annealer

    Here is my annealer using MGNZ's shield design. I have mounted it all in an ACM case I designed. The blue LED you see when the annealer is running is taken directly from the ZVS board to give a...

    Liked On: 08-07-2020, 10:33 AM

14. 
    gqhoon liked post by Norway On thread : Shooting in wind with hunting scopes

    Finally something a bit more relevant for NZ hunters: Dealing with wind & no tools. This will probably be 3-5 films total. Could save you a running animal. ...

    Liked On: 28-06-2020, 11:03 AM

15. 
    gqhoon liked post by Tahr On thread : Good find

    I saw this one drop in the scrub last night but I couldn't find it and Tilly just wanted to follow confusing hot trails. So I worked my way back to where I had shot it from and she straight away put...

    Liked On: 14-06-2020, 12:20 PM

Page 10 of 16 First 12345678910111213141516 Last

• Jump to page: