Greetings All, I really believe that whether you are destined to be a handloader is dertermined at conception. If we are handloaders then there is no point in fighting it as it is our destiny....
Liked On: 15-09-2022, 08:18 PM
Greetings All, I really believe that whether you are destined to be a handloader is dertermined at conception. If we are handloaders then there is no point in fighting it as it is our destiny....
Liked On: 15-09-2022, 04:48 PM
Greetings All, I really believe that whether you are destined to be a handloader is dertermined at conception. If we are handloaders then there is no point in fighting it as it is our destiny....
Liked On: 15-09-2022, 04:04 PM
Greetings All, I really believe that whether you are destined to be a handloader is dertermined at conception. If we are handloaders then there is no point in fighting it as it is our destiny....
Liked On: 15-09-2022, 03:01 PM
Greetings alanimal, The components that go into a handload all vary as do the rifles that they are fired in. Generally data for pressure tested loads will show similar top velocities but sometimes...
Liked On: 12-09-2022, 10:35 PM
Greetings Sideshow, Of the three powders you mention I would favour the N150 as it is the only one of the three powders that there seems to be factory data for the 7x57. That is just me though and...
Liked On: 10-09-2022, 05:53 PM
Yes there will be a bit more bullet jump but the blunt projectiles are pretty tolerant and usually shoot well seated away from the rifling. Crimp variation would be a bigger factor. Even with the Lee...
Liked On: 08-09-2022, 07:28 PM
Yes there will be a bit more bullet jump but the blunt projectiles are pretty tolerant and usually shoot well seated away from the rifling. Crimp variation would be a bigger factor. Even with the Lee...
Liked On: 08-09-2022, 07:22 PM
Greetings Sideshow, Of the three powders you mention I would favour the N150 as it is the only one of the three powders that there seems to be factory data for the 7x57. That is just me though and...
Liked On: 08-09-2022, 12:25 PM
Greetings Tertle, Assuming that the loads shown in the pic are yours I would try seating the projectles a little deeper so the case mouth is in the middle of the crimping groove. I would also ensure...
Liked On: 08-09-2022, 11:51 AM
Unlikely to make much difference. Projectiles in the same box are made in different dies so they all vary slightly so you are likely to get minute differences between rounds regardless. I assume that...
Liked On: 06-09-2022, 09:19 PM
Unlikely to make much difference. Projectiles in the same box are made in different dies so they all vary slightly so you are likely to get minute differences between rounds regardless. I assume that...
Liked On: 06-09-2022, 06:40 PM
Greetings again Scotts. I looked up the difference between the SAAMI maximum chamber and minimum case fror headspace an it amounted to 0.365 mm (0.014"). For the Creedmoor I would expect the...
Liked On: 06-09-2022, 05:45 PM
Greetings again Scotts. I looked up the difference between the SAAMI maximum chamber and minimum case fror headspace an it amounted to 0.365 mm (0.014"). For the Creedmoor I would expect the...
Liked On: 06-09-2022, 01:45 PM
Greetings All, I had a quick poke around on the interweb this morning and quickly found plenty of posts on Forums parroting the discontinuance of the Enduron powders. One even forcasted the...
Liked On: 05-09-2022, 05:48 PM