Nar, if you mince them up you get a lump of batter with a vague mussel taste, whole mussel bingo you get the full Monty and you could mix in to the raw mussels some garlic and sweet chilli sauce,...
Liked On: 18-03-2018, 09:33 AM
First dive in and get your mussels, I dive into Pack and save and also grab a pack of beer batter. Mix up homebrew beer batter or use that stuff you buy and set aside. Now setup and open the raw...
Liked On: 16-03-2018, 10:41 PM
First dive in and get your mussels, I dive into Pack and save and also grab a pack of beer batter. Mix up homebrew beer batter or use that stuff you buy and set aside. Now setup and open the raw...
Liked On: 16-03-2018, 09:12 PM
First dive in and get your mussels, I dive into Pack and save and also grab a pack of beer batter. Mix up homebrew beer batter or use that stuff you buy and set aside. Now setup and open the raw...
Liked On: 16-03-2018, 08:27 PM
First dive in and get your mussels, I dive into Pack and save and also grab a pack of beer batter. Mix up homebrew beer batter or use that stuff you buy and set aside. Now setup and open the raw...
Liked On: 16-03-2018, 08:27 PM
First dive in and get your mussels, I dive into Pack and save and also grab a pack of beer batter. Mix up homebrew beer batter or use that stuff you buy and set aside. Now setup and open the raw...
Liked On: 16-03-2018, 08:20 PM
First dive in and get your mussels, I dive into Pack and save and also grab a pack of beer batter. Mix up homebrew beer batter or use that stuff you buy and set aside. Now setup and open the raw...
Liked On: 16-03-2018, 08:10 PM
Put them in the for sale area and then we can order from there!, and pay as well. just a thought.
Liked On: 15-03-2018, 04:44 AM
OK Guys, octagonal done and crowned the muzzle, then shaper , but the good news is it fits in the stock. Now just have to make up the sights and under pins it will be good to go hunting with that big...
Liked On: 14-03-2018, 10:33 AM
Pedals, I think I`v got a electric motor around here some where!!. ;)
Liked On: 14-03-2018, 09:35 AM
Well bugger me days, obviously Chop3r you know your top off the line measuring stuff, those pegs are my twist ratio guides. One is touching the one on the rifling shaft , the crank handle is turned...
Liked On: 14-03-2018, 09:35 AM
OK Guys, octagonal done and crowned the muzzle, then shaper , but the good news is it fits in the stock. Now just have to make up the sights and under pins it will be good to go hunting with that big...
Liked On: 14-03-2018, 08:12 AM
OK Guys, octagonal done and crowned the muzzle, then shaper , but the good news is it fits in the stock. Now just have to make up the sights and under pins it will be good to go hunting with that big...
Liked On: 13-03-2018, 07:52 PM
All looks good, although the drill was 30" long I could only drill in 22", the oil and chip catcher stops going in farther. The drilled hole was .501" at the start and .4999" at the finished end, a...
Liked On: 10-03-2018, 07:59 AM
Took me a bit to work it out and a few small bearings on the slider got things working, had to make the small sprocket to get the right ratio and now its working a treat. Will have go at doing a few...
Liked On: 09-03-2018, 07:57 PM