homebrew.357
Member

1244 Likes

Page 1 of 83 12345678910111213141551 ... Last

• Jump to page:

1. 
   john m liked post by homebrew.357 On thread : Blank barrel

   You know I`ll have to agree with you, I`m slowly improving my system and thought the fast twist would cause problems ,but no and I`ll have to say this is the best barrel I have done. I`m very tempted...

   Liked On: 16-11-2023, 09:10 PM

2. 
   Woody liked post by homebrew.357 On thread : Blank barrel

   Well no, my state of the art cutters are made from T C tipped saw blades and as I`m hand cranking slowly through the barrel with my top of the range C N C set up there`s no wear on the cutter. My...

   Liked On: 16-11-2023, 08:09 PM

3. 
   Woody liked post by homebrew.357 On thread : Blank barrel

   You know I`ll have to agree with you, I`m slowly improving my system and thought the fast twist would cause problems ,but no and I`ll have to say this is the best barrel I have done. I`m very tempted...

   Liked On: 16-11-2023, 08:07 PM

4. 
   Woody liked post by homebrew.357 On thread : Blank barrel

   I suppose with the right set up they could be used, but I think they are hardened so no good for cut rifling and the time it takes I don`t need to practice. Maybe after I wear out the Sharps barrel...

   Liked On: 16-11-2023, 08:05 PM

5. 
   -BW- liked post by homebrew.357 On thread : Blank barrel

   Well no, my state of the art cutters are made from T C tipped saw blades and as I`m hand cranking slowly through the barrel with my top of the range C N C set up there`s no wear on the cutter. My...

   Liked On: 06-11-2023, 09:17 PM

6. 
   Micky Duck liked post by homebrew.357 On thread : Blank barrel

   Great stuff, keep practicing with a good load so you know there it`s hitting say at 50m`s then go and find some goats/deer. I want to see one of my barrels doing the deed .

   Liked On: 03-11-2023, 02:21 PM

7. 
   -BW- liked post by homebrew.357 On thread : Blank barrel

   At the back of the lathe is the setup for rifling register of the six groves, a bracket with a arm is bolted in place and the arm has a pin that locates and locks in a round disc with the evenly...

   Liked On: 03-11-2023, 11:47 AM

8. 
   -BW- liked post by homebrew.357 On thread : Blank barrel

   OK OK, Here`s a close up and personal look at the rifling system, first pic is the rear end where the cutter is pulled through the barrel. You can see the sine bar and slider assembly and the crank...

   Liked On: 03-11-2023, 11:47 AM

9. 
   -BW- liked post by homebrew.357 On thread : Blank barrel

   I suppose with the right set up they could be used, but I think they are hardened so no good for cut rifling and the time it takes I don`t need to practice. Maybe after I wear out the Sharps barrel...

   Liked On: 03-11-2023, 11:46 AM

10. 
    Micky Duck liked post by homebrew.357 On thread : 45/70 Subsonic

    The mould I have is the Lee d/c, C309-160-R, Dia .309, 160gr, My lead,(pipe) is mixed with a bit of linotype and tin to harden it up a bit, could go a bit harder to see if it casts to size and stop...

    Liked On: 08-07-2023, 06:11 PM

11. 
    Micky Duck liked post by homebrew.357 On thread : 45/70 Subsonic

    Talk about one rifle and post pic`s of another one! ,:O_O:. Here is my Marlin 3030. 70630, After the spruce up.

    Liked On: 08-07-2023, 05:54 PM

12. 
    Micky Duck liked post by homebrew.357 On thread : 45/70 Subsonic

    Yep , Bills the knife maker, and that 50m group was 60mm on the outer edge, at 100m it spreads to 150mm and I take a 6 0clock aim on target, at 50m and 100m it shoots 1-1/2 to 3" high. This is with...

    Liked On: 08-07-2023, 05:54 PM

13. 
    Micky Duck liked post by homebrew.357 On thread : 45/70 Subsonic

    Hi Rossi.45, Have to say no, not a long range rifle, not bad at 50m but spreads out a bit at 100m. It is a black powder cartridge so trying 65/70 grs 3f with lead bullets, 420gr and pp ones with 3031...

    Liked On: 08-07-2023, 05:51 PM

14. 
    Micky Duck liked post by homebrew.357 On thread : 45/70 Subsonic

    Hi rossi.45, I was just having you on, I was wondering if the action had been beefed up for the 45-70 cartridge. I will leave my .3030 as is, I call it "Sudden death" does the job really well in the...

    Liked On: 08-07-2023, 05:49 PM

15. 
    RUMPY liked post by homebrew.357 On thread : Baikal single shot rebarrel - Anyone done this?

    That barrel is chambered for 45-70 I think, should be good to go. I use 3031 powder and load up my Sharps with 40gr and a hollow base bullet.168406

    Liked On: 25-06-2022, 12:45 PM

Page 1 of 83 12345678910111213141551 ... Last

• Jump to page: