homebrew.357
Member

1244 Likes

Page 5 of 83 First 1234567891011121314151617181955 ... Last

• Jump to page:

1. 
   2post liked post by homebrew.357 On thread : Making a Rolling block rifle on my lathe.

   Yes I can get it to do most things, here`s one, It helps with my beer supplies,:) as I use shims to pack things up I have found that ali beer cans cut into strips are the best for this. Different...

   Liked On: 27-07-2020, 09:14 PM

2. 
   Micky Duck liked post by homebrew.357 On thread : Making a Rolling block rifle on my lathe.

   Yes I can get it to do most things, here`s one, It helps with my beer supplies,:) as I use shims to pack things up I have found that ali beer cans cut into strips are the best for this. Different...

   Liked On: 27-07-2020, 08:59 PM

3. 
   SixtyTen liked post by homebrew.357 On thread : Making a Rolling block rifle on my lathe.

   OK, so having milled out all the centre it needs to be square in the round corners, this was achieved by using a T/C tipped cutter from a saw blade first and then a small HSS square one to finish....

   Liked On: 23-07-2020, 05:13 PM

4. 
   SixtyTen liked post by homebrew.357 On thread : Making a Rolling block rifle on my lathe.

   Still in milling mode, have changed the cutter for a rounded tip one so puts a corner Radis to help stop cracking. This is now milled out to size ready for the hammer and breach block so may have...

   Liked On: 23-07-2020, 05:12 PM

5. 
   dannyb liked post by homebrew.357 On thread : Remington model 341 sportsmaster circa 1936-40

   Hell, all this reminds me of my first .22, it was a Remington Target Master single shot, knocked off quite a few bunnies on Waiheke Island about the 1960`s. used to buy a brick of 500 ICI 22 amo and...

   Liked On: 23-07-2020, 12:04 PM

6. 
   Micky Duck liked post by homebrew.357 On thread : Making a Rolling block rifle on my lathe.

   OK, so having milled out all the centre it needs to be square in the round corners, this was achieved by using a T/C tipped cutter from a saw blade first and then a small HSS square one to finish....

   Liked On: 22-07-2020, 06:25 PM

7. 
   SixtyTen liked post by homebrew.357 On thread : Making a Rolling block rifle on my lathe.

   So with that part milled out it`s really starting to look like it will do the job. Fear bit of work to do yet but it`s coming a long, here`s what it looks like so far and the pins are a snug fit so...

   Liked On: 14-07-2020, 03:23 PM

8. 
   Cordite liked post by homebrew.357 On thread : Making a Rolling block rifle on my lathe.

   So with that part milled out it`s really starting to look like it will do the job. Fear bit of work to do yet but it`s coming a long, here`s what it looks like so far and the pins are a snug fit so...

   Liked On: 10-07-2020, 11:24 PM

9. 
   Cordite liked post by homebrew.357 On thread : Making a Rolling block rifle on my lathe.

   Now that's it, a barrel is a tube with splines cut in the bore, what you do with it is up to you, good for watering the garden. If you asked me to make a action for you ,"NO WAY", I only make rifles...

   Liked On: 10-07-2020, 11:17 PM

10. 
    Magnus liked post by homebrew.357 On thread : Making a Rolling block rifle on my lathe.

    So with that part milled out it`s really starting to look like it will do the job. Fear bit of work to do yet but it`s coming a long, here`s what it looks like so far and the pins are a snug fit so...

    Liked On: 10-07-2020, 10:15 PM

11. 
    Micky Duck liked post by homebrew.357 On thread : Making a Rolling block rifle on my lathe.

    So with that part milled out it`s really starting to look like it will do the job. Fear bit of work to do yet but it`s coming a long, here`s what it looks like so far and the pins are a snug fit so...

    Liked On: 10-07-2020, 09:26 PM

12. 
    Mathias liked post by homebrew.357 On thread : Making a Rolling block rifle on my lathe.

    Still in milling mode, have changed the cutter for a rounded tip one so puts a corner Radis to help stop cracking. This is now milled out to size ready for the hammer and breach block so may have...

    Liked On: 09-07-2020, 09:28 PM

13. 
    timattalon liked post by homebrew.357 On thread : Making a Rolling block rifle on my lathe.

    Still in milling mode, have changed the cutter for a rounded tip one so puts a corner Radis to help stop cracking. This is now milled out to size ready for the hammer and breach block so may have...

    Liked On: 09-07-2020, 08:55 PM

14. 
    2post liked post by homebrew.357 On thread : Making a Rolling block rifle on my lathe.

    Still in milling mode, have changed the cutter for a rounded tip one so puts a corner Radis to help stop cracking. This is now milled out to size ready for the hammer and breach block so may have...

    Liked On: 09-07-2020, 08:53 PM

15. 
    SixtyTen liked post by homebrew.357 On thread : Making a Rolling block rifle on my lathe.

    The first mill cut out .650" slot and I needed .735" per the plans, so after a reset up to get it lined up on centre I mounted a broken mill cutter with only one cutting flute. Set in the four jaw...

    Liked On: 07-07-2020, 08:59 PM

Page 5 of 83 First 1234567891011121314151617181955 ... Last

• Jump to page: