homebrew.357
Member

1244 Likes

Page 70 of 83 First ... 2056575859606162636465666768697071727374757677787980818283 Last

• Jump to page:

1. 
   veitnamcam liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

   Just couldn`t stand the suspense of not knowing what my new mould would cast out at, so had a bit of lead casting today. Results, .463"dia, and the double cavity mould cast one at 425grs, and one at...

   Liked On: 03-02-2015, 08:09 PM

2. 
   mikee liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

   Just couldn`t stand the suspense of not knowing what my new mould would cast out at, so had a bit of lead casting today. Results, .463"dia, and the double cavity mould cast one at 425grs, and one at...

   Liked On: 03-02-2015, 07:06 PM

3. 
   res liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

   Just couldn`t stand the suspense of not knowing what my new mould would cast out at, so had a bit of lead casting today. Results, .463"dia, and the double cavity mould cast one at 425grs, and one at...

   Liked On: 03-02-2015, 07:02 PM

4. 
   veitnamcam liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

   Hi Guys, Hope you had a good xmas and put a dent in the brown ale supply, I need three homebrew kits at least to stock up my supply. Have done a bit more to my Sharps barrel, octagonal finished and...

   Liked On: 02-02-2015, 08:06 AM

5. 
   res liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

   Hi Guys, Hope you had a good xmas and put a dent in the brown ale supply, I need three homebrew kits at least to stock up my supply. Have done a bit more to my Sharps barrel, octagonal finished and...

   Liked On: 01-02-2015, 09:22 PM

6. 
   Gibo liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

   Hi Guys, Hope you had a good xmas and put a dent in the brown ale supply, I need three homebrew kits at least to stock up my supply. Have done a bit more to my Sharps barrel, octagonal finished and...

   Liked On: 01-02-2015, 08:54 PM

7. 
   Bryan liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

   Hi Guys, Hope you had a good xmas and put a dent in the brown ale supply, I need three homebrew kits at least to stock up my supply. Have done a bit more to my Sharps barrel, octagonal finished and...

   Liked On: 01-02-2015, 08:53 PM

8. 
   Tommy liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

   Hi .303 guy, I suppose there`s a lot of ways of doing this , like a sine ways rifling bar, just have to look on the internet for ideas. I just got lucky with my gearbox and bike bits , and the end...

   Liked On: 21-12-2014, 09:12 PM

9. 
   ishoot10s liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

   Hi .303 guy, I suppose there`s a lot of ways of doing this , like a sine ways rifling bar, just have to look on the internet for ideas. I just got lucky with my gearbox and bike bits , and the end...

   Liked On: 20-12-2014, 08:35 PM

10. 
    veitnamcam liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

    Hi .303 guy, I suppose there`s a lot of ways of doing this , like a sine ways rifling bar, just have to look on the internet for ideas. I just got lucky with my gearbox and bike bits , and the end...

    Liked On: 20-12-2014, 07:47 PM

11. 
    Shamus liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

    :killzonesmiley: Hell, with all this holy stuff around you need a gas mask on and a knife to cut the air. Speaking of cutting , there`s a pic of some real action cutting the octagonal so you know...

    Liked On: 13-12-2014, 07:54 PM

12. 
    rob270 liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

    Hi ishoot10s, No such luck mate, carn`t put the lathe in drive with the gear box locket up for cutting the octagonal , so yes I`m winding the saddle up and down, up and down, ext .ext,. Say one...

    Liked On: 13-12-2014, 11:37 AM

13. 
    Bryan liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

    Hi ishoot10s, No such luck mate, carn`t put the lathe in drive with the gear box locket up for cutting the octagonal , so yes I`m winding the saddle up and down, up and down, ext .ext,. Say one...

    Liked On: 11-12-2014, 11:49 AM

14. 
    Gibo liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

    Hi ishoot10s, No such luck mate, carn`t put the lathe in drive with the gear box locket up for cutting the octagonal , so yes I`m winding the saddle up and down, up and down, ext .ext,. Say one...

    Liked On: 11-12-2014, 11:30 AM

15. 
    Scouser liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

    Hi ishoot10s, No such luck mate, carn`t put the lathe in drive with the gear box locket up for cutting the octagonal , so yes I`m winding the saddle up and down, up and down, ext .ext,. Say one...

    Liked On: 11-12-2014, 11:10 AM

Page 70 of 83 First ... 2056575859606162636465666768697071727374757677787980818283 Last

• Jump to page: