homebrew.357
Member

1244 Likes

Page 75 of 83 First ... 256162636465666768697071727374757677787980818283 Last

• Jump to page:

1. 
   Scouser liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

   The junction box, Chip catcher full , motor and pump, 30019300223002530028, Lots of chips, :cool:,Homebrew.357.

   Liked On: 15-10-2014, 02:49 PM

2. 
   Scouser liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

   Ok, some more pic`s, The outlet tube has a clear window so I can see the chips flowing out, keeps me happy. Oil and chips go down to the chip strainer and oil goes into the tank in a go around...

   Liked On: 15-10-2014, 02:48 PM

3. 
   Bryan liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

   Ok, some more pic`s, The outlet tube has a clear window so I can see the chips flowing out, keeps me happy. Oil and chips go down to the chip strainer and oil goes into the tank in a go around...

   Liked On: 15-10-2014, 08:32 AM

4. 
   AzumitH liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

   The junction box, Chip catcher full , motor and pump, 30019300223002530028, Lots of chips, :cool:,Homebrew.357.

   Liked On: 14-10-2014, 09:58 PM

5. 
   ishoot10s liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

   The junction box, Chip catcher full , motor and pump, 30019300223002530028, Lots of chips, :cool:,Homebrew.357.

   Liked On: 14-10-2014, 09:31 PM

6. 
   veitnamcam liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

   The junction box, Chip catcher full , motor and pump, 30019300223002530028, Lots of chips, :cool:,Homebrew.357.

   Liked On: 14-10-2014, 09:23 PM

7. 
   veitnamcam liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

   Ok, some more pic`s, The outlet tube has a clear window so I can see the chips flowing out, keeps me happy. Oil and chips go down to the chip strainer and oil goes into the tank in a go around...

   Liked On: 14-10-2014, 09:22 PM

8. 
   Toby liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

   The junction box, Chip catcher full , motor and pump, 30019300223002530028, Lots of chips, :cool:,Homebrew.357.

   Liked On: 14-10-2014, 08:53 PM

9. 
   Toby liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

   Ok, some more pic`s, The outlet tube has a clear window so I can see the chips flowing out, keeps me happy. Oil and chips go down to the chip strainer and oil goes into the tank in a go around...

   Liked On: 14-10-2014, 08:28 PM

10. 
    Toby liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

    Ok, The barrel is set up ready to drill, so here is the setup for the gun drill. The following steady and fixed one are mounted on the lathe to help guide the gun drill and keep it straight . The...

    Liked On: 14-10-2014, 07:45 PM

11. 
    gadgetman liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

    HI, Yes they recommend 0.0002" per revaluation, barrel speeds of 2/5000 rpms, and 1000 psi oil presser . The drill goes in one inch per minute and it takes 1/2 hour per barrel, I a lot slower....

    Liked On: 13-10-2014, 01:35 PM

12. 
    ishoot10s liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

    Hi, Now that I had things set up for drilling with the gun drill ready to go, had to think about the in feed rate. The drill must go in very slowly for small chips that can be flushed out with the...

    Liked On: 08-10-2014, 05:52 PM

13. 
    ishoot10s liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

    A few more pic`s. 2982929830, And all in place.2983129832, that's It.

    Liked On: 08-10-2014, 05:52 PM

14. 
    veitnamcam liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

    HI, Yes they recommend 0.0002" per revaluation, barrel speeds of 2/5000 rpms, and 1000 psi oil presser . The drill goes in one inch per minute and it takes 1/2 hour per barrel, I a lot slower....

    Liked On: 08-10-2014, 09:07 AM

15. 
    Toby liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

    A few more pic`s. 2982929830, And all in place.2983129832, that's It.

    Liked On: 08-10-2014, 09:00 AM

Page 75 of 83 First ... 256162636465666768697071727374757677787980818283 Last

• Jump to page: