Hi, Now that I had things set up for drilling with the gun drill ready to go, had to think about the in feed rate. The drill must go in very slowly for small chips that can be flushed out with the...
Liked On: 08-10-2014, 08:59 AM
Well hi there C Diem, I`v got two foots in them there hills as well, just a jafa. Ok, to get things moving on my lathe bed ways and to hold the gun drill, I made up to sets of ali blocks that fitted...
Liked On: 04-10-2014, 08:22 PM
2963129632Ok, The drill guide is mounted on my angle bracket and it sits in front of the 4 jaw chuck, but first the guide stub in set in the chuck true. The drill guide and bracket is set in front of...
Liked On: 01-10-2014, 07:42 PM
Yer, your right Kotuku, they are like a bloody rugby scrum, all falling all over then selfs , could put some gun powder in :ka boom: some where and lite it, mite get a bang. The gun drill guide...
Liked On: 30-09-2014, 11:48 AM
Hi All, This is how I drilled, reamed and cut rifle a barrel in my lathe. My lathe is belt driven and .900" centres ,I made some attachments to fit on the lathe so I could do this, never thinking it...
Liked On: 30-09-2014, 11:39 AM
Hi Res, I`m drilling this barrel now, about 16" to go and no It`s not my first one, check my other threads. The barrel stock is trued up in the lathe at each end and a fine cut and faced for...
Liked On: 30-09-2014, 11:38 AM
Hi Res, I`m drilling this barrel now, about 16" to go and no It`s not my first one, check my other threads. The barrel stock is trued up in the lathe at each end and a fine cut and faced for...
Liked On: 29-09-2014, 06:10 PM
Hi Res, I`m drilling this barrel now, about 16" to go and no It`s not my first one, check my other threads. The barrel stock is trued up in the lathe at each end and a fine cut and faced for...
Liked On: 29-09-2014, 02:20 PM
Hi Res, I`m drilling this barrel now, about 16" to go and no It`s not my first one, check my other threads. The barrel stock is trued up in the lathe at each end and a fine cut and faced for...
Liked On: 29-09-2014, 02:19 PM
Hi Res, I`m drilling this barrel now, about 16" to go and no It`s not my first one, check my other threads. The barrel stock is trued up in the lathe at each end and a fine cut and faced for...
Liked On: 29-09-2014, 02:06 PM
Hi All, This is how I drilled, reamed and cut rifle a barrel in my lathe. My lathe is belt driven and .900" centres ,I made some attachments to fit on the lathe so I could do this, never thinking it...
Liked On: 29-09-2014, 08:51 AM
Hi All, This is how I drilled, reamed and cut rifle a barrel in my lathe. My lathe is belt driven and .900" centres ,I made some attachments to fit on the lathe so I could do this, never thinking it...
Liked On: 29-09-2014, 08:05 AM
Hi All, This is how I drilled, reamed and cut rifle a barrel in my lathe. My lathe is belt driven and .900" centres ,I made some attachments to fit on the lathe so I could do this, never thinking it...
Liked On: 29-09-2014, 12:38 AM
Hi All, This is how I drilled, reamed and cut rifle a barrel in my lathe. My lathe is belt driven and .900" centres ,I made some attachments to fit on the lathe so I could do this, never thinking it...
Liked On: 28-09-2014, 09:25 PM
Hi guys , I`m going to start on making the barrel for this Sharps rifle , so will start a new post just for this and give you an idea of how it was done on my lathe. Will stop this thread from...
Liked On: 28-09-2014, 12:24 AM