homebrew.357
Member

1244 Likes

Page 58 of 83 First ... 84445464748495051525354555657585960616263646566676869707172 ... Last

• Jump to page:

1. 
   res liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

   Hi Guys, I am still doing some bits on the rifle, mainly the stock wood fitting form the black walnut I got. Have roughly cut out the stock and forearm bits and fitting the forearm first, I cut it to...

   Liked On: 18-12-2015, 03:15 AM

2. 
   Frogfeatures liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

   Hi Guys, I am still doing some bits on the rifle, mainly the stock wood fitting form the black walnut I got. Have roughly cut out the stock and forearm bits and fitting the forearm first, I cut it to...

   Liked On: 17-12-2015, 09:24 PM

3. 
   Frogfeatures liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

   Hi boys, Coming right down to bluff, hop over to Steward Island and back up the west coast, about 3/4 months on the road, and will be taking my computer with me so I can pm you guys with the watering...

   Liked On: 14-12-2015, 09:35 PM

4. 
   Tommy liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

   Hi boys, Coming right down to bluff, hop over to Steward Island and back up the west coast, about 3/4 months on the road, and will be taking my computer with me so I can pm you guys with the watering...

   Liked On: 14-12-2015, 09:07 PM

5. 
   kotuku liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

   Hi all, I`m milling the second slot for the forearm and then will be doing the back and front sight slots, when all this is done I can fit the barrel, I think, there`s always some thing I forget but...

   Liked On: 05-12-2015, 08:13 AM

6. 
   Beaker liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

   Hi Scouser, Pal old mate!, I love toolmakers, they have lots of used milling bits that are gold to a hobby machinist!!, yes that's all I`m doing this with, second hand mill bits, new ones are to...

   Liked On: 02-12-2015, 08:48 PM

7. 
   Wildman liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

   Hi Scouser, Pal old mate!, I love toolmakers, they have lots of used milling bits that are gold to a hobby machinist!!, yes that's all I`m doing this with, second hand mill bits, new ones are to...

   Liked On: 02-12-2015, 07:18 AM

8. 
   Scouser liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

   Hi, Recoil pad?, Who said he could have one, no pain no gain and I will be able to judge my loads by his yells.:omg::XD:. The last bits to do, milling a dove tail slot for the under lever breech...

   Liked On: 01-12-2015, 08:20 AM

9. 
   kotuku liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

   Ok, Thanks Spanners, My past tests have not gone to bad,:ka boom: I`ll have plenty of band aids on hand.:ouch...it hurts: Here`s a pic of my last test, the tester is still running I think! :mouse:....

   Liked On: 17-11-2015, 10:21 AM

10. 
    res liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

    Ok, Thanks Spanners, My past tests have not gone to bad,:ka boom: I`ll have plenty of band aids on hand.:ouch...it hurts: Here`s a pic of my last test, the tester is still running I think! :mouse:....

    Liked On: 17-11-2015, 12:46 AM

11. 
    res liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

    Hi, When I get a chance I`m going to ether rebore and recut the rifling or make a new barrel for the Hawkens. Have been playing around making a tang sight for the Sharps and now I have drilled and...

    Liked On: 17-11-2015, 12:46 AM

12. 
    res liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

    Hi guys, A bit more, After milling the flat I had to mill a slot for the ejector as well then it would close in when the breech was closed. When all was working I tried a case and it ejected...

    Liked On: 17-11-2015, 12:45 AM

13. 
    kotuku liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

    Hi, When I get a chance I`m going to ether rebore and recut the rifling or make a new barrel for the Hawkens. Have been playing around making a tang sight for the Sharps and now I have drilled and...

    Liked On: 16-11-2015, 06:25 AM

14. 
    300CALMAN liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

    Hi guys, A bit more, After milling the flat I had to mill a slot for the ejector as well then it would close in when the breech was closed. When all was working I tried a case and it ejected...

    Liked On: 15-11-2015, 09:44 PM

15. 
    Beaker liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

    Hi, When I get a chance I`m going to ether rebore and recut the rifling or make a new barrel for the Hawkens. Have been playing around making a tang sight for the Sharps and now I have drilled and...

    Liked On: 15-11-2015, 09:28 PM

Page 58 of 83 First ... 84445464748495051525354555657585960616263646566676869707172 ... Last

• Jump to page: