The under lever fits in a slot under the receiver , so set up and with a off centred mill and cut out to full depth. At the top of this slot a tee cut is milled for the lever spring , I made up a...
Liked On: 30-07-2015, 09:03 PM
The under lever fits in a slot under the receiver , so set up and with a off centred mill and cut out to full depth. At the top of this slot a tee cut is milled for the lever spring , I made up a...
Liked On: 30-07-2015, 07:12 PM
The junction box, Chip catcher full , motor and pump, 30019300223002530028, Lots of chips, :cool:,Homebrew.357.
Liked On: 30-07-2015, 03:11 PM
Hi, The receiver is a bit over weight with a goodly lot that has to come off, so sent it to boot camp for a work out to lose a bit, but they grabbed me as well so I had a good work out as well. Good...
Liked On: 29-07-2015, 11:13 PM
And to those who think I have a electric band saw, :XD:, NO I don`t, I just put a hack saw blade into my bush camping saw and I`m the champion arm wrestler in the retired men's club. :super:....
Liked On: 22-07-2015, 11:39 AM
Hi Kotuku, No I`m doing it the other way around, what I`v bottled is going into my blood. Now have also ground a radis on the front of the receiver and milled out a large flat on the left side to ...
Liked On: 20-07-2015, 08:29 PM
Hi, The receiver is a bit over weight with a goodly lot that has to come off, so sent it to boot camp for a work out to lose a bit, but they grabbed me as well so I had a good work out as well. Good...
Liked On: 20-07-2015, 08:29 PM
Hi Kotuku, Bet there are a few narwhals faces in the windy city, :XD: those mainland boys just upped there kilts and got stuck in and I bet they put those beer handles to good use. :beer:. Now the...
Liked On: 06-07-2015, 10:58 PM
I don`t think it goes for our Auckland stallion, hear he has spent $20.000 of tax payers money on a new bedroom in his council offices, he would be wise to keep away from our cannon shoots, the boys...
Liked On: 18-06-2015, 11:05 PM
Hi Kotuku, When I went in to have my first hip joint removed, I said "What do you do with the old one " , yer, I`v got it in my draw , thinking how can I use it in the Sharps build.:D Make a great...
Liked On: 16-06-2015, 10:35 PM
Hi Kotuku, When I went in to have my first hip joint removed, I said "What do you do with the old one " , yer, I`v got it in my draw , thinking how can I use it in the Sharps build.:D Make a great...
Liked On: 16-06-2015, 09:20 PM
Hi Kotuku, When I went in to have my first hip joint removed, I said "What do you do with the old one " , yer, I`v got it in my draw , thinking how can I use it in the Sharps build.:D Make a great...
Liked On: 16-06-2015, 09:05 PM
After some careful but slow thread cutting I finally was able to screw in the barrel with plenty of grease so it would not jam up on me as I wanted a tight thread. It now screws in nicely with a bit...
Liked On: 15-06-2015, 10:29 AM
Hi Guys, Back from a few days up north at Kerikeri, saw a weather window so loaded up my small caravan with eggs, bacon, sausages, onions and when I got to the camp site, there`s a home kill butcher...
Liked On: 15-06-2015, 10:29 AM
Hi, As you can see I have threaded the barrel end ready to fit in the receiver and as I said it will not fit on my face plate, but with right low down cunning, it did!," there`s ways and means". So...
Liked On: 15-06-2015, 10:27 AM