homebrew.357
Member

1244 Likes

Page 65 of 83 First ... 155152535455565758596061626364656667686970717273747576777879 ... Last

• Jump to page:

1. 
   Scouser liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

   Hi, hopefully this is the precision I can do, b/block mounted on top slide after marking out centre for barrel hole and then drill with small and larger drills. Change to milling cutters to plunge...

   Liked On: 15-06-2015, 10:26 AM

2. 
   Frogfeatures liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

   After some careful but slow thread cutting I finally was able to screw in the barrel with plenty of grease so it would not jam up on me as I wanted a tight thread. It now screws in nicely with a bit...

   Liked On: 13-06-2015, 01:04 PM

3. 
   308 liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

   After some careful but slow thread cutting I finally was able to screw in the barrel with plenty of grease so it would not jam up on me as I wanted a tight thread. It now screws in nicely with a bit...

   Liked On: 04-06-2015, 07:26 PM

4. 
   Beaker liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

   Hi, As you can see I have threaded the barrel end ready to fit in the receiver and as I said it will not fit on my face plate, but with right low down cunning, it did!," there`s ways and means". So...

   Liked On: 04-06-2015, 09:31 AM

5. 
   Beaker liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

   After some careful but slow thread cutting I finally was able to screw in the barrel with plenty of grease so it would not jam up on me as I wanted a tight thread. It now screws in nicely with a bit...

   Liked On: 04-06-2015, 09:31 AM

6. 
   Bryan liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

   After some careful but slow thread cutting I finally was able to screw in the barrel with plenty of grease so it would not jam up on me as I wanted a tight thread. It now screws in nicely with a bit...

   Liked On: 03-06-2015, 11:03 PM

7. 
   Blaser liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

   After some careful but slow thread cutting I finally was able to screw in the barrel with plenty of grease so it would not jam up on me as I wanted a tight thread. It now screws in nicely with a bit...

   Liked On: 03-06-2015, 09:32 PM

8. 
   veitnamcam liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

   Hi, hopefully this is the precision I can do, b/block mounted on top slide after marking out centre for barrel hole and then drill with small and larger drills. Change to milling cutters to plunge...

   Liked On: 01-06-2015, 11:52 PM

9. 
   Tommy liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

   Hi, As you can see I have threaded the barrel end ready to fit in the receiver and as I said it will not fit on my face plate, but with right low down cunning, it did!," there`s ways and means". So...

   Liked On: 01-06-2015, 09:30 PM

10. 
    res liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

    Hi, hopefully this is the precision I can do, b/block mounted on top slide after marking out centre for barrel hole and then drill with small and larger drills. Change to milling cutters to plunge...

    Liked On: 01-06-2015, 02:37 PM

11. 
    deepsouthaussie liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

    Hi, hopefully this is the precision I can do, b/block mounted on top slide after marking out centre for barrel hole and then drill with small and larger drills. Change to milling cutters to plunge...

    Liked On: 30-05-2015, 10:11 PM

12. 
    Toby liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

    Hi, hopefully this is the precision I can do, b/block mounted on top slide after marking out centre for barrel hole and then drill with small and larger drills. Change to milling cutters to plunge...

    Liked On: 30-05-2015, 09:29 PM

13. 
    kotuku liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

    Oops, forgot the pic`s, 36718, 36721, 36722, 36723, And the day went with a bang!, Homebrew.357.

    Liked On: 19-05-2015, 07:06 PM

14. 
    Scouser liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

    Hi, Its a lot of fun alright , will post some pic`s on a new thread. Here is my best group bench shooting with ten shots aiming at the black cross, 6 o'clock, mind fore shots are missing,:o have to...

    Liked On: 19-05-2015, 02:58 PM

15. 
    Scouser liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

    Oops, forgot the pic`s, 36718, 36721, 36722, 36723, And the day went with a bang!, Homebrew.357.

    Liked On: 19-05-2015, 02:57 PM

Page 65 of 83 First ... 155152535455565758596061626364656667686970717273747576777879 ... Last

• Jump to page: