imaca
Member

446 Likes

Page 1 of 30 123456789101112131415 ... Last

• Jump to page:

1. 
   imaca liked post by Husky1600#2 On thread : An odd response..

   Funny that - I had the same sort of thing happen as well. Was hunting a nice little gully, had a good idea there were some deer in the matagouri below us so started to tip over a rock to send down...

   Liked On: 24-04-2025, 08:37 AM

2. 
   imaca liked post by XR500 On thread : An odd response..

   Yeah, insects they'll turn themselves inside out for. The whereabouts of 4 legged food type animals are of far far less interest to them. In the late 1990's I almost trod on an enormous skink when...

   Liked On: 24-04-2025, 08:36 AM

3. 
   imaca liked post by 199p On thread : Tongariro National Park

   It dosnt make for very good tv if they dont catch it on camera tho. Preddy sure getting it on film would be the 1st job of shooting a hunting tv show Sent from my SM-S928B using Tapatalk

   Liked On: 22-04-2025, 11:36 AM

4. 
   imaca liked post by McNotty On thread : Always Check!

   Bullet would’ve opened up the hole just nicely for you :thumbsup:

   Liked On: 15-04-2025, 08:21 PM

5. 
   imaca liked post by 25/08 IMP On thread : When to anneal.

   Tony at Tenpointone in Wellington Sent from my CPH2531 using Tapatalk

   Liked On: 09-04-2025, 11:53 AM

6. 
   imaca liked post by T.FOYE On thread : When to anneal.

   The bit i hate is chamfering. Its needed but that is the biggest contributor to neck tension variation IMO. Try a batch not chamfered vs chamfered and record your MV. I put it forward that it makes...

   Liked On: 07-04-2025, 08:51 AM

7. 
   imaca liked post by T.FOYE On thread : When to anneal.

   Yeah anneal then resize. i once did a test to see if i got any better results on target and i couldn't see any (annealing last before seating). I did notice bugger all neck tension which isn't a...

   Liked On: 07-04-2025, 08:51 AM

8. 
   imaca liked post by 7mmsaum On thread : When to anneal.

   Anneal first then size You get the benefit of less springback, which can be as much as 1.3 thou on unannealed brass And your first resize after annealing is your best chance to measure your...

   Liked On: 07-04-2025, 08:51 AM

9. 
   imaca liked post by Moutere On thread : When to anneal.

   Anneal then resize.

   Liked On: 07-04-2025, 08:51 AM

10. 
    imaca liked post by Ryan_Songhurst On thread : An epic couple of weeks with some ups and downs..

    Don't manage to get off farm very often so had been really looking forward to the wapiti ballot this year as my sister and I had drawn Narrows Creek for the first period. Cassie turned up the day...

    Liked On: 30-03-2025, 10:08 AM

11. 
    imaca liked post by norsk On thread : when your neighbour discharges a firearm recklessly and the cops do......

    To stop poachers,spray paint your gates rainbow colours and call them gay-ates. Gay-ates will not be entered without consent! Hate crime=jail time!

    Liked On: 11-03-2025, 07:58 PM

12. 
    imaca liked post by gimp On thread : Act submission points

    Here's some of the brief bullet points I've thought about for the consultation. I have deliberately not written them out in full here and omitted some things/changed my language because you'll have...

    Liked On: 16-02-2025, 02:01 PM

13. 
    imaca liked post by Scouser On thread : Predator Free

    Just joined Auckland central parks animal pest control project, targeting possums and rats with none poisonous baits (peanut butter for rats, cinnamon dusted apples for possums) Get my trap line...

    Liked On: 16-02-2025, 08:52 AM

14. 
    imaca liked post by Springy On thread : Trip Report

    Family hike on the weekend. 7 hours in the hot sun. Lucky we bought a tarp for sun shelter on the way. Got to hut, had dinner etc. Glassing from the hut, spotted pigs. Shot a pig across a...

    Liked On: 05-02-2025, 06:09 PM

15. 
    imaca liked post by Happy Jack On thread : DoC Hunting Permit Survey

    My answer to that question was along the lines. You want us to do your work and then pay for the privilege.

    Liked On: 01-02-2025, 08:15 AM

Page 1 of 30 123456789101112131415 ... Last

• Jump to page: