Jaco Goosen
Member

466 Likes

Page 21 of 32 First ... 7891011121314151617181920212223242526272829303132 Last

• Jump to page:

1. 
   Jaco Goosen liked post by charliehorse On thread : Point Blank

   Headed up the bush 2 days before Xmas for an evening hunt with the calibre of all calibres at my side:thumbsup: Would probably be my last for a few weeks. Went up after dinner and was on the...

   Liked On: 28-12-2021, 02:04 PM

2. 
   Jaco Goosen liked post by 55six On thread : A short film produced with thermal camera and scope.

   The rabbits were shot at 50-100m. At the the 33 second mark there is a paddock of rabbits at around 300m. We had a strong tail wind and they didn't stick around long. The polaris scope we were using...

   Liked On: 22-12-2021, 02:04 AM

3. 
   Jaco Goosen liked post by Neil lesslie On thread : Howa 1500 bedding.

   Jaco,stug and sixtyten are correct. Jaco because he already does it this way, stug because he understands the forces acting on the action by the action screws,and sixtyten because you need clearance...

   Liked On: 19-12-2021, 07:44 AM

4. 
   Jaco Goosen liked post by dannyb On thread : Anyone keen to rent a labradar?

   To be honest I don't think its a great idea, too risky, accidents happen, and way to many dodgy people out there. Just look at the accounts on here that have recently been hacked for starters. It's...

   Liked On: 19-12-2021, 07:42 AM

5. 
   Jaco Goosen liked post by wayno On thread : 7mm SAUM, WSM, Blaser Magnum, Rem Mag and 284 Superpig Discussion

   I run a 30/284 and for the 30 fan i think this would be a good all rounder as with the right twist barrel you could run 130 to 180plus bullets , to suit . The 284 is a very versatile case

   Liked On: 13-11-2021, 12:37 PM

6. 
   Jaco Goosen liked post by gundoc On thread : Possible muzzle threads on .574 barrel?

   1/2"x28 TPI would be good and still leave a decent shoulder for the suppressor to contact. 9/16" and 14mm will both leave a shoulder that is too narrow to get a positive register.

   Liked On: 08-11-2021, 08:43 PM

7. 
   Jaco Goosen liked post by gundoc On thread : Ruger Ranch II Bolt face - do I have a problem?

   The bolt face damage is totally due to gas cutting by primer leakage. The bolt face could be repaired by careful TIG welding, doing just a small area at a time to avoid over-heating the bolt and...

   Liked On: 01-11-2021, 10:44 PM

8. 
   Jaco Goosen liked post by Jhon On thread : Ruger Ranch II Bolt face - do I have a problem?

   Great, thanks! That's what I needed to know.

   Liked On: 01-11-2021, 10:43 PM

9. 
   Jaco Goosen liked post by quentin On thread : Shooting for "groups"

   If I'm using a round target without horizontal or vertical lines (that can be used to align with the reticle posts), I find my groupings open up as the point of aim gets bigger as the ragged hole...

   Liked On: 01-11-2021, 12:38 PM

10. 
    Jaco Goosen liked post by longshot On thread : Rifle cleaning 101 - school me!

    The same way different guns like different ammo, so too do different guns like different cleaning regimes, what one person swears by because it works for him, may not work for you. The two main...

    Liked On: 26-10-2021, 01:02 PM

11. 
    Jaco Goosen liked post by Seventenths On thread : Stock builders

    Early Sako stocks are one of the best model stocks in my opinion!

    Liked On: 25-10-2021, 09:11 PM

12. 
    Jaco Goosen liked post by 40mm On thread : Should movie stars be allowed to outsource personal responsibility?

    You are forgetting the dead woman, she was also at fault for not checking the thing. I would not let anyone point one at me without checking it myself first, and personally handing it to them.

    Liked On: 25-10-2021, 10:27 AM

13. 
    Jaco Goosen liked post by gundoc On thread : Should movie stars be allowed to outsource personal responsibility?

    Definitely the fault of the set armourer who has total responsibility for the firearms and blank ammunition on set. Actors, by and large, are nothing more than presentable monkeys who perform as the...

    Liked On: 25-10-2021, 10:23 AM

14. 
    Jaco Goosen liked post by 55six On thread : Looks interesting...

    We have mini action hinged floor plates coming

    Liked On: 14-10-2021, 04:27 PM

15. 
    Jaco Goosen liked post by zimmer On thread : Tap and drill for scope mounts

    Genuine Lyttelton marked?

    Liked On: 12-10-2021, 05:02 PM

Page 21 of 32 First ... 7891011121314151617181920212223242526272829303132 Last

• Jump to page: