JD300
Member

122 Likes

Page 1 of 9 123456789 Last

• Jump to page:

1. 
   JD300 liked post by akaroa1 On thread : Cast Lead Thread ?

   No speed limit on powder coated gas checked bullets other than running out of case capacity

   Liked On: 20-10-2022, 08:17 AM

2. 
   JD300 liked post by T.FOYE On thread : Cast Lead Thread ?

   I ran my new MP 415gn hollowpoint (pentagonal cone shape) across the radar yesterday. These had cc1 200 primers, 'cost effective' winchester brass (10th cycle), N130 VV powder. Carefully waiting 4min...

   Liked On: 20-10-2022, 08:17 AM

3. 
   JD300 liked post by T.FOYE On thread : Cast Lead Thread ?

   208217 Fairly good groups at 100m. It's pretty hold sensitive being such a light rifle but it's fine for hunting out to 200m imo

   Liked On: 20-10-2022, 08:15 AM

4. 
   JD300 liked post by akaroa1 On thread : Cast Lead Thread ?

   I have put a lot of very big lumps of PC lead down range last week Finally found what my 500 3" BPE likes Nitro for black load 450 grain PC bullets sized .510 Made a new front globe sight for...

   Liked On: 04-10-2022, 09:07 PM

5. 
   JD300 liked post by akaroa1 On thread : Cast Lead Thread ?

   More powder coated cast lead success stories This group from my Baikal 30-30 self build carbine Bullets are Saeco #311 mould 165 grain Powder Coated Gas Check Sized .309 No fancy load...

   Liked On: 04-10-2022, 09:07 PM

6. 
   JD300 liked post by Jhon On thread : Cast Lead Thread ?

   Why do both? GC and PC?

   Liked On: 29-09-2022, 09:46 AM

7. 
   JD300 liked post by T.FOYE On thread : Cast Lead Thread ?

   I found the checks too tricky to seat afterwards so I just stick em on at initial sizing. I do dust the pc off with a bit of paper towel as I want the bases as flat as possible. Doesn't look totally...

   Liked On: 29-09-2022, 09:46 AM

8. 
   JD300 liked post by akaroa1 On thread : Cast Lead Thread ?

   .309 and .311 PC gas check cast bullets 206551

   Liked On: 26-09-2022, 08:45 AM

9. 
   JD300 liked post by Crekyhills On thread : 45 & 40gr 224 to swap

   205656these of any use to you? I don't reload so not looking for an exchange. Cheers Chris

   Liked On: 10-09-2022, 08:14 PM

10. 
    JD300 liked post by T.FOYE On thread : Cast Lead Thread ?

    Awesome mould. Bit of faff setting up the hole makers as they came completely disassembled but they just screw together. Bullets came out well. It's got one of those spring washers so the tension...

    Liked On: 06-09-2022, 10:10 PM

11. 
    JD300 liked post by akaroa1 On thread : Cast Lead Thread ?

    Multiple lines under a certain caliber are all in that caliber So yes 6x 38 moulds

    Liked On: 06-09-2022, 07:46 PM

12. 
    JD300 liked post by akaroa1 On thread : Cast Lead Thread ?

    I just had to go to the workshop to check out a mould size and decided to make a master list of whats there to save going out and seeing in the future I have never bothered with gas checks despite...

    Liked On: 06-09-2022, 07:45 PM

13. 
    JD300 liked post by akaroa1 On thread : Cast Lead Thread ?

    I would be interested in measuring the bore rider 45 500s and seeing the mould Not so much for my 1885 45-70 but that style would be good in a 45-90

    Liked On: 05-09-2022, 11:40 AM

14. 
    JD300 liked post by akaroa1 On thread : Cast Lead Thread ?

    So is anyone casting a gas check 30 cal and how hard are you casting it and how fast are you pushing it ? Just brought a Saeco #311 double cavity mould Should cast a 165 grain gas check bore...

    Liked On: 05-09-2022, 09:32 AM

15. 
    JD300 liked post by T.FOYE On thread : Cast Lead Thread ?

    Those laser thermos are good for the outside but you wanna reading from down in the mix. I got this one for $35usd plus $10 postage. Arrived in less than a week ...

    Liked On: 04-09-2022, 01:26 PM

Page 1 of 9 123456789 Last

• Jump to page: