JD300
Member

122 Likes

Page 2 of 9 First 123456789 Last

• Jump to page:

1. 
   JD300 liked post by akaroa1 On thread : Cast Lead Thread ?

   I cast a heap of 38 cal 300 grain bullets during the week to make up this dummy round to try on a dummy chamber I cut Wanted to make sure my chamber reamer was on spec for the bullets I want to...

   Liked On: 02-09-2022, 11:00 AM

2. 
   JD300 liked post by T.FOYE On thread : Cast Lead Thread ?

   Am very much looking fwd to this arriving soon. It's the only hollowpoint mould MP has in stock atm for the .458 fans. They do have a more sleek model but it's on backorder (and makes a lighter...

   Liked On: 02-09-2022, 10:54 AM

3. 
   JD300 liked post by T.FOYE On thread : Cast Lead Thread ?

   Check Amazon eh. I got a lyman electronic one with a probe and it does the job well. Really cheap too considering what it does

   Liked On: 02-09-2022, 10:54 AM

4. 
   JD300 liked post by T.FOYE On thread : Cast Lead Thread ?

   I found I was making good bullets while I was regularly fluxing and skimming off the dross. Keep it mixing. Don't let your top screw on your lee melter wind out too much (less is more). It's a good...

   Liked On: 02-09-2022, 10:54 AM

5. 
   JD300 liked post by akaroa1 On thread : Cast Lead Thread ?

   205124

   Liked On: 02-09-2022, 10:49 AM

6. 
   JD300 liked post by Micky Duck On thread : Cast Lead Thread ?

   there is a guide to using lead pencils to test your hardness...but shooternz makes a good projectile..if thumnail is good enough for him....well its good enough for me.

   Liked On: 01-09-2022, 02:15 PM

7. 
   JD300 liked post by shooternz On thread : Cast Lead Thread ?

   Hi JD, Wellcome to the Cast bullet world you are in for a big learning curve, Like Tedz50 said don't melt it all down together melt each type to see what you have I have been caught a few times...

   Liked On: 01-09-2022, 02:15 PM

8. 
   JD300 liked post by T.FOYE On thread : Cast Lead Thread ?

   I started with unknown hardness linotype and thought it wouldn't take long to dilute it /test with a lee tester. It took all day! Next time I'll start with the pure and work up to about 12BHN....

   Liked On: 01-09-2022, 02:15 PM

9. 
   JD300 liked post by T.FOYE On thread : Cast Lead Thread ?

   I've just done the same and gotten into casting. Heaps on YouTube and other online sources. The accuracy is great and for the 4570 you won't be losing any mv especially if you crimp.

   Liked On: 29-08-2022, 04:58 PM

10. 
    JD300 liked post by The bomb On thread : Cast Lead Thread ?

    Pm nzshooter here on the forum,he is the local cast bullet guru

    Liked On: 22-08-2022, 11:24 PM

11. 
    JD300 liked post by Jhon On thread : Cast Lead Thread ?

    Suggest you get you across to these US sites for casting, https://castboolits.gunloads.com/ https://forum.castbulletassoc.org/ and others There's decades of info covering everything you...

    Liked On: 22-08-2022, 11:24 PM

12. 
    JD300 liked post by Tedz50 On thread : Cast Lead Thread ?

    Just a word of caution,do not mix large batches unless you know whats in it.I have ruined good lead by mixing in a small amount of 22 bullets,also pipe joints which contained zinc. Good score though...

    Liked On: 22-08-2022, 11:24 PM

13. 
    JD300 liked post by hotsoup On thread : Best frame pack ???? whats every one using Lastenkraxe?

    Stone glacier, kifaru, kuiu, mystery ranch, outdoorsman's, exo Can't go wrong with the above

    Liked On: 25-07-2022, 11:07 AM

14. 
    JD300 liked post by dannyb On thread : Best frame pack ???? whats every one using Lastenkraxe?

    Yup i run a Tatonka bison too bloody great pack and carrys big loads well

    Liked On: 25-07-2022, 11:07 AM

15. 
    JD300 liked post by Happy Jack On thread : Best frame pack ???? whats every one using Lastenkraxe?

    dannyb has that issue too he is 6'7" I think, or least he is a giant to people of normal stature like me. :bouaaaaah:

    Liked On: 25-07-2022, 11:07 AM

Page 2 of 9 First 123456789 Last

• Jump to page: