Longranger
Member

77 Likes

Page 1 of 6 123456 Last

• Jump to page:

1. 
   apkiwi liked post by Longranger On thread : Ridge in once fired .303 brass

   A collett die has to move the brass from a larger diameter to a smaller diameter and the brass has to go somewhere and that is in the form of ridges. There should be three or four depending on the...

   Liked On: 03-02-2024, 10:46 AM

2. 
   Micky Duck liked post by Longranger On thread : Pressure Variations and Load Data

   Hi Young fella......the bore will make a difference. I had a local .284 barrel that could never reach optimum velocity, and expanded primer pockets well before the desired velocity was reached. I...

   Liked On: 23-01-2024, 09:22 PM

3. 
   6.5 CRD liked post by Longranger On thread : Pierced ginex primers

   If that middle case did not have excessive headspace it was too hot. Powder can be temperature sensitive and be OK in winter....too hot in summer. You need to check the headspace measurement on a...

   Liked On: 08-01-2024, 08:20 AM

4. 
   veryfuturistic liked post by Longranger On thread : Local range

   Franklin Rifle Club, Akarana City Rifle Club, Waiuku Pistol Club

   Liked On: 01-11-2023, 04:22 PM

5. 
   Treakle13 liked post by Longranger On thread : Local range

   Franklin Rifle Club, Akarana City Rifle Club, Waiuku Pistol Club

   Liked On: 26-10-2023, 09:06 AM

6. 
   rupert liked post by Longranger On thread : Case Neck runout with redding type s bushing die

   I agree...my chambers are all tight requiring neck turned brass, and Redding S type dies with loose bushings just can't and never produced zero runout on the necks.......FLS first and then if you...

   Liked On: 03-07-2023, 10:27 PM

7. 
   Old_School liked post by Longranger On thread : Mildew on my rifles. Damp rid seems to do nothing

   Been there done that.....firstly I used an un-shielded 7w LED bulb and it took the colour from a wooden stock adjacent to it. Be very careful with LED it seems to have some detrimental light wave...

   Liked On: 02-05-2023, 05:26 PM

8. 
   Micky Duck liked post by Longranger On thread : Vizsla free to good home

   Photos uploaded now......this is a really serious dog...couldn't get him to smile

   Liked On: 04-01-2023, 05:26 PM

9. 
   Micky Duck liked post by Longranger On thread : Full Electric LDV ute

   The Future......CNG, LNG, LPG conversions....not so long ago the Guvmint sudsidised, and promoted these planet saving ideas. Watch this space....!

   Liked On: 26-12-2022, 12:17 PM

10. 
    tetawa liked post by Longranger On thread : Vizsla free to good home

    Sorry no photos yet ....Male dog, all jabs, and neutered, viewing in Auckland. Had a PM but no further messages. NZHS site has been down and not sure my reply was received.

    Liked On: 25-12-2022, 08:01 AM

11. 
    bigbear liked post by Longranger On thread : Vizsla free to good home

    Sorry no photos yet ....Male dog, all jabs, and neutered, viewing in Auckland. Had a PM but no further messages. NZHS site has been down and not sure my reply was received.

    Liked On: 24-12-2022, 06:29 PM

12. 
    stingray liked post by Longranger On thread : Vizsla free to good home

    Sorry no photos yet ....Male dog, all jabs, and neutered, viewing in Auckland. Had a PM but no further messages. NZHS site has been down and not sure my reply was received.

    Liked On: 24-12-2022, 06:26 PM

13. 
    rugerman liked post by Longranger On thread : Vizsla free to good home

    Sorry no photos yet ....Male dog, all jabs, and neutered, viewing in Auckland. Had a PM but no further messages. NZHS site has been down and not sure my reply was received.

    Liked On: 24-12-2022, 06:14 PM

14. 
    grandpamac liked post by Longranger On thread : What are you using for pressure estimation in your handloads.

    Yes I was thinking you really need to know what you are doing using the primer as indication of pressure.....headspace is the determinator of primer flattening as well as hot loads. Too much...

    Liked On: 14-12-2022, 02:56 PM

15. 
    Micky Duck liked post by Longranger On thread : ballistic calculator's can be wrong

    T12 should be fine... Marty Henry as above probably not enough speed....chronograph some factory and if groups better load to that speed. Berger barrel twist calculator is not a ballistic calculator....

    Liked On: 16-10-2022, 02:56 PM

Page 1 of 6 123456 Last

• Jump to page: