Magnetite
Member

135 Likes

Page 6 of 9 First 123456789 Last

• Jump to page:

1. 
   MB liked post by Magnetite On thread : 3 vs 5 shot groups

   I was looking over some of my old targets for load development (seating depth specifically) comparing 3 and 5 shot groups. And from what I could see I would have reached the same conclusions with 3...

   Liked On: 22-02-2022, 08:24 PM

2. 
   RugerM77 liked post by Magnetite On thread : Load ladder, annealing conundrum

   New brass will add a whole new set of variables. Changing one thing at a time is best (I quite often fail at this). Check your annealing then do the ladder.

   Liked On: 10-02-2022, 04:36 PM

3. 
   Micky Duck liked post by Magnetite On thread : Notched case - should I use it?

   For $2-$3 do you want to play that game with your face? I wouldn’t.

   Liked On: 06-02-2022, 08:49 PM

4. 
   cambo liked post by Magnetite On thread : DIY Primer Pocket Cleaner

   A nice thick piece of copper cable works well too.

   Liked On: 02-01-2022, 02:09 PM

5. 
   onlyhsh liked post by Magnetite On thread : Suppressor and load dev

   I haven’t done load development unsuppressed, but I have shot the load without it. The harmonics are definitely different and the POI shift was huge, ~10cm at 100m.

   Liked On: 07-11-2021, 11:51 AM

6. 
   25 /08 IMP liked post by Magnetite On thread : Thank you - First Handloads

   I wouldn’t overlook that flat spot between 43.2-43.5gr. It may prove to be more stable under varying conditions.

   Liked On: 14-09-2021, 04:49 PM

7. 
   mopheadrob liked post by Magnetite On thread : Notched case - should I use it?

   For $2-$3 do you want to play that game with your face? I wouldn’t.

   Liked On: 02-09-2021, 02:32 PM

8. 
   Tahr liked post by Magnetite On thread : 6.5x55: 2213SC is too slow for 120gr, I say BAH!

   Sako 75

   Liked On: 25-08-2021, 11:26 AM

9. 
   veitnamcam liked post by Magnetite On thread : 6.5x55: 2213SC is too slow for 120gr, I say BAH!

   It maybe, but It has an SD of zero. That’s unheard of consistency.

   Liked On: 24-08-2021, 11:38 PM

10. 
    Micky Duck liked post by Magnetite On thread : Reloading begginer info needed

    I don't like buy once cry once. How can you buy once if you don't know what you want. Better to start off cheap (try someone else's gear, secondhand etc.) and then invest in quality once you have a...

    Liked On: 24-08-2021, 08:51 PM

11. 
    Jhon liked post by Magnetite On thread : Hdy 129g SST in 6.5x55 Swede

    I use the deep creek method for finding the lands. 1. Strip down your bolt (firing pin, extractor. Everything that will put pressure on the case). 2. Find a sized case where the bolt drops freely...

    Liked On: 24-08-2021, 07:56 PM

12. 
    Jhon liked post by Magnetite On thread : 6.5x55 SE Sanity Check

    I don't mind at all. Hopefully I have been clear enough (In my first post I mentioned it's over max and again when I posted over max data). When venturing past max, my new approach is to cross...

    Liked On: 23-08-2021, 10:25 PM

13. 
    rewa liked post by Magnetite On thread : 6.5x55: 2213SC is too slow for 120gr, I say BAH!

    It maybe, but It has an SD of zero. That’s unheard of consistency.

    Liked On: 23-08-2021, 09:52 PM

14. 
    rewa liked post by Magnetite On thread : 6.5x55: 2213SC is too slow for 120gr, I say BAH!

    Everyone seems to think 2209 is the go to ADI powder for sub 140gr projectiles in the 6.5x55. 2213SC worked really well for the 129gr Interlock. The siren of accuracy was calling, so I thought why...

    Liked On: 23-08-2021, 09:51 PM

15. 
    rewa liked post by Magnetite On thread : 6.5x55 SE Sanity Check

    I got round to some accuracy testing and was surprised at the results. Both were 6 shot groups at 100m. I played around with the seating depth for both powders but settled on using the same for each....

    Liked On: 23-08-2021, 09:46 PM

Page 6 of 9 First 123456789 Last

• Jump to page: