Magnetite
Member

135 Likes

Page 9 of 9 First 123456789

• Jump to page:

1. 
   Micky Duck liked post by Magnetite On thread : Soot On Case Bodies

   It did do it while I was doing some incremental testing with 2209. But it didn't seem consistent. There is a small amount of soot on the neck of the factory rounds (Hornady Superformance). The...

   Liked On: 11-04-2021, 09:25 PM

2. 
   dannyb liked post by Magnetite On thread : Jump

   I would suggest option B in the interest of saving powder (If powder is readily available A). I would stick with the Sierra data as there is no guarantee the Nosler or Hornady will behave like a...

   Liked On: 22-02-2021, 01:13 PM

3. 
   Ftx325 liked post by Magnetite On thread : Wannabe reloader - gear advice please

   The Dan Newberry has a good write up on the different tools you need and how necessary they are. Tools of the Trade (http://www.ocwreloading.com/tools-of-the-trade.html) Also the Hornady...

   Liked On: 11-11-2020, 10:53 AM

4. 
   Moa Hunter liked post by Magnetite On thread : 6.5x55 SE Sanity Check

   I got round to some accuracy testing and was surprised at the results. Both were 6 shot groups at 100m. I played around with the seating depth for both powders but settled on using the same for each....

   Liked On: 24-10-2020, 02:39 PM

5. 
   Tuidog liked post by Magnetite On thread : 2213sc in 6.5x55?

   I did some seating depth testing with 2213sc and 129gr projectiles. It looks like you will need to adjust it between 2209 and 2213sc. Initially it looks like 2213sc noticeably more accurate. I hope...

   Liked On: 18-10-2020, 12:30 AM

6. 
   Tuidog liked post by Magnetite On thread : 2213sc in 6.5x55?

   I did a comparison of 2209 and 2213sc with 129gr bullets. It may be of interest to you: https://www.nzhuntingandshooting.co.nz/f10/6-5x55-se-sanity-check-61340/index2.html#post1062511

   Liked On: 10-10-2020, 05:36 PM

7. 
   mimms2 liked post by Magnetite On thread : Calculating pressures in hand loads

   I haven't tested these methods, but they may be of interest: Simple Trick for Monitoring Pressure of Your Rifle Reloads | Hodgdon Reloading...

   Liked On: 24-09-2020, 10:52 PM

8. 
   rupert liked post by Magnetite On thread : 6.5x55 SE Sanity Check

   Obligatory disclaimer: What you put in your chamber is your business. Some of these loads are over ADI's maximum. 2213SC powder 4 shots each charge: Grains fps SD ES 46.0 2475 29.9 63 46.5...

   Liked On: 12-09-2020, 04:45 PM

9. 
   stevodog liked post by Magnetite On thread : Preferred barrel bullet weight

   148329

   Liked On: 03-09-2020, 11:39 AM

10. 
    charliehorse liked post by Magnetite On thread : Preferred barrel bullet weight

    148329

    Liked On: 02-09-2020, 10:10 PM

11. 
    Moa Hunter liked post by Magnetite On thread : Preferred barrel bullet weight

    148329

    Liked On: 02-09-2020, 10:03 PM

12. 
    Frogfeatures liked post by Magnetite On thread : Preferred barrel bullet weight

    148329

    Liked On: 02-09-2020, 09:28 PM

13. 
    grandpamac liked post by Magnetite On thread : 6.5x55 SE Sanity Check

    I botched some of those numbers. Corrected below: Grains 42.5 43 43.5 44 44.5 45 45.5 Max Spread 1.172 0.994 1.287 1.926 1.326 1.496 1.135 Height ...

    Liked On: 02-09-2020, 06:29 PM

14. 
    grandpamac liked post by Magnetite On thread : 6.5x55 SE Sanity Check

    I did check the group sizes at 100yards but I don't trust them entirely as the wind was up. Grains 42.5 43 43.5 44 44.5 45 45.5 Max Spread ...

    Liked On: 02-09-2020, 06:29 PM

15. 
    grandpamac liked post by Magnetite On thread : 6.5x55 SE Sanity Check

    I finally found a place to do some testing. I've only tested the 2209 so far. I stopped at 45.5gr which was doing 2842fps from a 580mm barrel with suppressor. This matches up with the ADI max load...

    Liked On: 01-09-2020, 02:33 PM

Page 9 of 9 First 123456789

• Jump to page: