Magnetite
Member

125 Likes

Page 8 of 9 First 123456789 Last

• Jump to page:

1. 
   kiwi303 liked post by Magnetite On thread : Cleaning brass...

   Wipe it with a rag, run a case neck brush through it. Proceed to reloading.

   Liked On: 13-05-2021, 11:05 AM

2. 
   Micky Duck liked post by Magnetite On thread : Cleaning brass...

   Wipe it with a rag, run a case neck brush through it. Proceed to reloading.

   Liked On: 12-05-2021, 09:57 PM

3. 
   chainsaw liked post by Magnetite On thread : Cleaning brass...

   Wipe it with a rag, run a case neck brush through it. Proceed to reloading.

   Liked On: 12-05-2021, 05:23 PM

4. 
   mimms2 liked post by Magnetite On thread : Cleaning brass...

   Wipe it with a rag, run a case neck brush through it. Proceed to reloading.

   Liked On: 12-05-2021, 04:04 PM

5. 
   Tikka7mm08 liked post by Magnetite On thread : Soot On Case Bodies

   Looks like I forgot to mention the most important part, the suppressor. Thanks for the help.

   Liked On: 12-04-2021, 11:14 AM

6. 
   Micky Duck liked post by Magnetite On thread : Soot On Case Bodies

   It did do it while I was doing some incremental testing with 2209. But it didn't seem consistent. There is a small amount of soot on the neck of the factory rounds (Hornady Superformance). The...

   Liked On: 11-04-2021, 09:25 PM

7. 
   dannyb liked post by Magnetite On thread : Jump

   I would suggest option B in the interest of saving powder (If powder is readily available A). I would stick with the Sierra data as there is no guarantee the Nosler or Hornady will behave like a...

   Liked On: 22-02-2021, 01:13 PM

8. 
   Ftx325 liked post by Magnetite On thread : Wannabe reloader - gear advice please

   The Dan Newberry has a good write up on the different tools you need and how necessary they are. Tools of the Trade (http://www.ocwreloading.com/tools-of-the-trade.html) Also the Hornady...

   Liked On: 11-11-2020, 10:53 AM

9. 
   Moa Hunter liked post by Magnetite On thread : 6.5x55 SE Sanity Check

   I got round to some accuracy testing and was surprised at the results. Both were 6 shot groups at 100m. I played around with the seating depth for both powders but settled on using the same for each....

   Liked On: 24-10-2020, 02:39 PM

10. 
    Tuidog liked post by Magnetite On thread : 2213sc in 6.5x55?

    I did some seating depth testing with 2213sc and 129gr projectiles. It looks like you will need to adjust it between 2209 and 2213sc. Initially it looks like 2213sc noticeably more accurate. I hope...

    Liked On: 18-10-2020, 12:30 AM

11. 
    Tuidog liked post by Magnetite On thread : 2213sc in 6.5x55?

    I did a comparison of 2209 and 2213sc with 129gr bullets. It may be of interest to you: https://www.nzhuntingandshooting.co.nz/f10/6-5x55-se-sanity-check-61340/index2.html#post1062511

    Liked On: 10-10-2020, 05:36 PM

12. 
    mimms2 liked post by Magnetite On thread : Calculating pressures in hand loads

    I haven't tested these methods, but they may be of interest: Simple Trick for Monitoring Pressure of Your Rifle Reloads | Hodgdon Reloading...

    Liked On: 24-09-2020, 10:52 PM

13. 
    rupert liked post by Magnetite On thread : 6.5x55 SE Sanity Check

    Obligatory disclaimer: What you put in your chamber is your business. Some of these loads are over ADI's maximum. 2213SC powder 4 shots each charge: Grains fps SD ES 46.0 2475 29.9 63 46.5...

    Liked On: 12-09-2020, 04:45 PM

14. 
    stevodog liked post by Magnetite On thread : Preferred barrel bullet weight

    148329

    Liked On: 03-09-2020, 11:39 AM

15. 
    charliehorse liked post by Magnetite On thread : Preferred barrel bullet weight

    148329

    Liked On: 02-09-2020, 10:10 PM

Page 8 of 9 First 123456789 Last

• Jump to page: