MGNZ
Member

30 Likes

Page 2 of 2 First 12

• Jump to page:

1. 
   MGNZ liked post by chainsaw On thread : General approach to powder selection for a new load

   +1 for info on this forum - there are some very knowledgeable folks with solid experience who are happy to share their knowledge. I’ve reloaded for about 5 yrs now and for the 12 or so different...

   Liked On: 28-11-2017, 10:16 AM

2. 
   MGNZ liked post by Boaraxa On thread : General approach to powder selection for a new load

   iv been reloading off & on for years but still an amateur with the bare basic gear , never had a chrony so always for accuracy though I do tend to look up the charts & pic a faster combo , always...

   Liked On: 28-11-2017, 10:16 AM

3. 
   MGNZ liked post by R93 On thread : General approach to powder selection for a new load

   To be honest there generally is a lot of info on load development on the net. Especially for something as commom as the .270 I only shoot a few centerfire rifles and apart from one of them I found...

   Liked On: 28-11-2017, 09:44 AM

4. 
   MGNZ liked post by gimp On thread : Film 41: Long Range Rimfire Rabbits

   I went for a walk this evening between rain showers, and shot some "long range" rabbits with my custom Savage MkII .22LR - "long range" in this case being between 60 and 150 metres. Film: ...

   Liked On: 17-10-2017, 05:24 PM

5. 
   MGNZ liked post by Dermastor On thread : Gong Shooting in Auckland

   An update on my previous post for you steel shooters. We at "Akarana - City Rile Club" have been able to increase the frequency of our shoots over the Summer season to weekly even if its just a...

   Liked On: 28-09-2017, 01:40 PM

6. 
   MGNZ liked post by WallyR On thread : Woodhill block 2

   Way back in the day, a work mate got a ballot (think it was the blue outlined block on your OP). Borrowed a 30/06, borrowed some 165gn SP off the owner and on the appointed day - off we went....

   Liked On: 26-06-2017, 11:18 AM

7. 
   MGNZ liked post by Allgood On thread : Woodhill block 2

   Pity you didnt post up earlier as I could have given you some info. Havent been on here much as I am looking after my elderly parents. Allgood.

   Liked On: 25-06-2017, 02:07 PM

8. 
   MGNZ liked post by Rushy On thread : Auckland shooting club membership fees

   I have just been invited to join (registered my interest a few months back) so have paid the fees. I will use the ranges with pistol, shotgun and AR15 for IPSC and have provided the club with...

   Liked On: 29-04-2017, 09:24 AM

9. 
   MGNZ liked post by Whanganui On thread : NI forum chrony

   will be going to MGNZ next

   Liked On: 11-02-2017, 01:43 PM

10. 
    MGNZ liked post by Sasquatch On thread : Cases being marked after chambering

    Funny last night I was watching this: https://www.youtube.com/watch?v=PDKBrKtN1OA It may help if you can get your hands on some Cerrosafe Alloy

    Liked On: 17-01-2017, 08:45 PM

11. 
    MGNZ liked post by MSL On thread : Cases being marked after chambering

    If it was something in your chamber there would be marking from the shoulder down to where the dent is. When you draw the bolt back does the case pop up as it exits the chamber? Many rifles dent the...

    Liked On: 17-01-2017, 08:26 PM

12. 
    MGNZ liked post by gadgetman On thread : Cases being marked after chambering

    I see another lighter dent about the case diameter further back. Scope mount screws protruding and being connected at some stage?

    Liked On: 17-01-2017, 08:26 PM

13. 
    MGNZ liked post by zimmer On thread : Cases being marked after chambering

    Initially go KISS. If is happens when not firing as well that is good. Mark the base in one spot with a felt tipped marker or just use the first letter of the case makers name. Insert case with...

    Liked On: 17-01-2017, 08:26 PM

14. 
    MGNZ liked post by Marty Henry On thread : Cases being marked after chambering

    Looks like an indentation which means somethings stuck to the chamber wall. Im guessing this hasnt happened from new? My suggestion is its probably a bit of brass searf from a case put the chamber...

    Liked On: 17-01-2017, 01:07 PM

15. 
    MGNZ liked post by johnd On thread : Cases being marked after chambering

    Then it must be something in the chamber, do you have a chamber brush ? Not a bore brush, but one that fits the chamber size? It cant be a "dent' in the chamber as that would leave a bulged spot on...

    Liked On: 17-01-2017, 01:07 PM

Page 2 of 2 First 12

• Jump to page: