mimms2
Banned

1231 Likes

Page 11 of 83 First 1234567891011121314151617181920212223242561 ... Last

• Jump to page:

1. 
   mimms2 liked post by Fssprecision On thread : Hi from Northland

   Here you go, long and the shorter piggers 179727

   Liked On: 26-09-2021, 12:21 PM

2. 
   mimms2 liked post by Fssprecision On thread : Hi from Northland

   A quick hi to all, I am based up in Whangarei, originally from the UK (ex Aerospace Engineer) my main interests are firearms repairs and modifications. I have developed all sorts over the years and...

   Liked On: 26-09-2021, 11:32 AM

3. 
   mimms2 liked post by keengunNic On thread : Shortened 7mm08 advice

   Hey mate, i love my 17" 7mm08 its super light, nimble as heck and shoots like a dream. As for loads, i havnt shot any factory loads through it. I shoot the 162 amax and its good to just under 600m...

   Liked On: 26-09-2021, 09:50 AM

4. 
   mimms2 liked post by Micky Duck On thread : Can you help me choose my next build

   so you already have a T3 in 308.......job done...suppress it if its not already and go and shoot lots o rounds at paper.....any animal out in open to 400 yards going to be in big trouble....how far...

   Liked On: 25-09-2021, 05:26 PM

5. 
   mimms2 liked post by Rated M for Magnum On thread : 7mm RUM. And the 195G EOL

   Because magnum :XD:

   Liked On: 23-09-2021, 08:02 PM

6. 
   mimms2 liked post by Mooseman On thread : Can you help me choose my next build

   Tikka , Sako would be good contenders but for the ranges you mention I think the Creedmoor may be lacking in power. 300 Win and 7mm Rem would be good for the longer range stuff but as stated above...

   Liked On: 22-09-2021, 10:23 PM

7. 
   mimms2 liked post by zimmer On thread : Issues Seating Cast Bullets

   Need to use a die such as Lymans M die to create a .308 clearance step in the case mouth. I think Lee may do something that will do a similar job. New brass can be hard to load with the first...

   Liked On: 22-09-2021, 08:29 PM

8. 
   mimms2 liked post by Makros On thread : Issues Seating Cast Bullets

   Many catridges where you use cast bullets use an expanding die after sizing prior to seating. It looks to me like the case mouth is undersized compared to the bullet and then pressure of seating is...

   Liked On: 22-09-2021, 08:28 PM

9. 
   mimms2 liked post by Rush On thread : Outdated question on the Police firearms test

   Leave the firearm out and put the children in the safe.

   Liked On: 22-09-2021, 07:30 PM

10. 
    mimms2 liked post by timattalon On thread : Outdated question on the Police firearms test

    Dead is better Perhaps the way to look at these questions is not "What is the correct answer?" but rather "What answer is the testing person wanting you to pick?" All three options are requirements...

    Liked On: 22-09-2021, 07:28 PM

11. 
    mimms2 liked post by Micky Duck On thread : Remington 700 sticky bolt dry fire

    so whats it like if you close bolt with trigger pulled....so it does same thing WITHOUT pin dropping with snap....eg it slides gently forward as bolt closes...

    Liked On: 21-09-2021, 11:00 PM

12. 
    mimms2 liked post by jono7 On thread : Remington 700 sticky bolt dry fire

    How hard to open? Tried a light lube on the back of the locking lugs and bolt cam surfaces by the shroud?

    Liked On: 21-09-2021, 11:00 PM

13. 
    mimms2 liked post by Cigar On thread : Remington 700 sticky bolt dry fire

    Firing pin jamming in hole in bolt face, because it moves further forwards with no primer to stop it?

    Liked On: 21-09-2021, 10:59 PM

14. 
    mimms2 liked post by 7mmsaum On thread : Remington 700 sticky bolt dry fire

    Has the bolt been stripped and cleaned and lubed properly ?

    Liked On: 21-09-2021, 10:59 PM

15. 
    mimms2 liked post by hotbarrels On thread : Last word on Kai Iwi Lakes, Northland

    As a kid about 40 years ago, we used to go over to the lakes with the Acclimatisation Society scientist to do the yearly trout survey that set the quota for the trout stocking. We used to set out a...

    Liked On: 21-09-2021, 08:33 PM

Page 11 of 83 First 1234567891011121314151617181920212223242561 ... Last

• Jump to page: