About mimms2

Basic Information


About mimms2
Location:
Tai Tokerau
Occupation:
For Hire

Statistics


Total Posts
Total Posts
5,863
Posts Per Day
3.47
General Information
Last Activity
18-12-2021 06:10 AM
Join Date
24-09-2019
Referrals
1

1231 Likes

  1. mimms2
    mimms2 liked post by Micky Duck On thread : 1:8 vs 1:12 in 223
    awesome rifle...snap it up QUICKLY... I too have zastava and have shot pigs and deer with it...no problem dedicated big stuff round is now a 50grn ttsx.....they awesome...my varmit rounds are 50grn...
    Liked On: 23-08-2020, 08:42 PM
  2. mimms2
    mimms2 liked post by Joe_90 On thread : 1:8 vs 1:12 in 223
    My CZ527 is 1:12, runs really well on 55gn soft points. Red sbs fallow deer tip over with neck shots. Found out pigs are tough buggers and need to get one in the ear if broadside. Ferrets just pop...
    Liked On: 23-08-2020, 08:42 PM
  3. mimms2
    mimms2 liked post by Scout On thread : 1:8 vs 1:12 in 223
    Hell for over 30yrs there was only the slower twist barrel & most people didn't even know what you meant if you asking about twist rate, some type of Black Art !! Some wondered why the 30/06 shot...
    Liked On: 23-08-2020, 08:07 PM
  4. mimms2
    mimms2 liked post by Woody On thread : Photos of your dog
    147880 Thor (black gwp) and Burl, passed away Nov 2019.
    Liked On: 23-08-2020, 08:06 PM
  5. mimms2
    mimms2 liked post by outlander On thread : What distance do you shoot game animals?
    My trusty 25-303 with a 90 gr bullet...shoot a sparrow off it. Probably unscrew the caps at 1000 or so with a 75 gr.
    Liked On: 23-08-2020, 08:04 PM
  6. mimms2
    mimms2 liked post by oraki On thread : Advice on a savge 223 wtb
    For their price point, they go alright.....bloody good to be honest. I’ve got one here that’s taken 6 Tahr (kids and nanny’s), dozen or so deer and dozens of wallabies. Probably close to 150 or so....
    Liked On: 22-08-2020, 07:07 PM
  7. mimms2
    mimms2 liked post by rugerman On thread : Photos of your dog
    People were often surprised to hear I could leave my dinner on the chair while I went out of the room to get something, and none of my dogs would eat it. I also fed my dogs off my plate so they knew...
    Liked On: 19-08-2020, 09:23 PM
  8. mimms2
    mimms2 liked post by Hiawatha On thread : McMillan stock etc
    Hi folks, I posted on here recently looking for a McMillan Hunters Edge stock for my rifle. I was directed by others here to Tracey Short of Dead Eye Dicks who stocks them. Too often we say...
    Liked On: 19-08-2020, 06:11 PM
  9. mimms2
    mimms2 liked post by XR500 On thread : Wool, wool, wool.
    Its hard to draw parallels between clothing that works in super cold, super dry conditions like in Russia, Canada, Scandinavia etc and little ol NZ where temps will hover around zero on a bad day,...
    Liked On: 19-08-2020, 02:26 PM
  10. mimms2
    mimms2 liked post by Nugget connaisseur On thread : Photos of your dog
    Sorry badly worded. I prefer a prong collar minor pressure corrections can be used, not the "check" correction. 10x easier to be consistent with and i have found dogs react to it better. I don't...
    Liked On: 19-08-2020, 05:25 AM
  11. mimms2
    mimms2 liked post by Micky Duck On thread : Photos of your dog
    I dislike the name choker chain...but both my dogs wear theirs all the time... no rotton smelly hair underneath as they breath (collar AND dog)...council tag goes in the end the clip goes onto. re...
    Liked On: 18-08-2020, 08:07 PM
  12. mimms2
    mimms2 liked post by gonetropo On thread : New to the forum. Jeremy
    from canterbury to auckland and you admit it !! 10/10 for bravery. 0 out of 10 for taste :P :P :P welcome
    Liked On: 17-08-2020, 06:33 PM
  13. mimms2
    mimms2 liked post by Tentman On thread : Building a shorty 22 (what barrel length)
    Just occasionally a rifle won't shoot where you cut it, a second shorter cut might get into a "good" section of barrel . . . .
    Liked On: 17-08-2020, 02:50 PM
  14. mimms2
    mimms2 liked post by gonetropo On thread : CNC lathes
    CNC machines are like testing jigs for electronics, great if you want to do 100's or 1000's of something but useless for the occasional build or repair
    Liked On: 16-08-2020, 10:51 PM
  15. mimms2
    mimms2 liked post by Nugget connaisseur On thread : Photos of your dog
    I have no experience with Pointers but other high energy dogs. Dogs like people are on a spectrum even within the breed. So liking other dogs and energy requirements will vary but most likely be...
    Liked On: 16-08-2020, 12:58 PM

08-10-2019


27-09-2019


25-09-2019



No results to display...
Welcome to NZ Hunting and Shooting Forums! We see you're new here, or arn't logged in. Create an account, and Login for full access including our FREE BUY and SELL section Register NOW!!