mopheadrob
Member

728 Likes

Page 15 of 49 First 1234567891011121314151617181920212223242526272829 ... Last

• Jump to page:

1. 
   mopheadrob liked post by moosemeat On thread : Tahr success

   224399 Hi All, I’ve been on the forum for over 3 yrs now and finally made it to the South Island and bagged me a 8 yr old tahr with 12 inch on his best side just under on the other couldn’t be more...

   Liked On: 22-05-2023, 05:17 PM

2. 
   mopheadrob liked post by Tall kiwi On thread : ResQLink PLB Battery replacement - $50 off

   Just an FYI for those that need a replacement battery for their ResQLink PLB - The guys over at Wilco Marine are doing a 2023 roar special and are discounting their battery replacement service by...

   Liked On: 02-05-2023, 01:59 PM

3. 
   mopheadrob liked post by Scott Cowan On thread : Nice 12Stag at 744y 6.5 - so am I unethical now guys?

   Ok, I’m sticking my neck out sharing this, and no I’m not Bunji reincarnated lol. On my roar trip I opted to hunt the open lands due to some health restrictions I’m working through. Even tho I was...

   Liked On: 02-05-2023, 01:58 PM

4. 
   mopheadrob liked post by Jhon On thread : Annealing after sizing?

   When I first loaded 303B with a press, about 15 yrs ago, I was using 1940s or thereabouts CAC Boxer primed brass and 170gn cast GC boolits. I was very new to reloading rifle. I did 10 with no real...

   Liked On: 20-04-2023, 02:12 PM

5. 
   mopheadrob liked post by andyanimal31 On thread : Annealing after sizing?

   I do own and use my AMP machine and what convinces me of why it's so Good is the science behind it all. The book that Alex wrote gives an amazing insight into how it all came about and why it is...

   Liked On: 19-04-2023, 04:38 PM

6. 
   mopheadrob liked post by Pommy On thread : Annealing after sizing?

   AMP will tell you that their machine actually makes the brass softer than is ideal, knowing that you are about to size the case. Sizing then brings up the hardness to the right point. So dong the...

   Liked On: 19-04-2023, 04:38 PM

7. 
   mopheadrob liked post by zimmer On thread : Annealing after sizing?

   He doesn't actually say the the sizing process doesn't cause alteration in ductility, just the firing process has a more a significant work hardening effect. However, I have one Ackley chambering....

   Liked On: 19-04-2023, 04:38 PM

8. 
   mopheadrob liked post by dannyb On thread : Annealing after sizing?

   Whilst I agree amp is the gold standard, I wouldn't go as far as to say anything else is ineffective, I have been hot salt annealing for a while now and like everything in reloading consistency is...

   Liked On: 18-04-2023, 02:24 PM

9. 
   mopheadrob liked post by andyanimal31 On thread : Annealing after sizing?

   To be fair any body that is thinking of annealing needs to look at the AMP website and get some scientific data on annealing.. The blow torch method is proven to be an ineffective hit and miss...

   Liked On: 18-04-2023, 10:48 AM

10. 
    mopheadrob liked post by 6.5 CRD On thread : Annealing after sizing?

    Not sure what effect annealing after sizing would have, but another +1 for annealing before sizing over here.

    Liked On: 18-04-2023, 10:48 AM

11. 
    mopheadrob liked post by Jaco Goosen On thread : Annealing after sizing?

    Always try to anneal before sizing - this way you'll be able to control the spring back after sizing. Most reloaders does not use a decapping die and thus sizes the cases to remove the primer...

    Liked On: 18-04-2023, 10:48 AM

12. 
    mopheadrob liked post by Dicko On thread : Annealing after sizing?

    Annealing before sizing is the way to go. Annealing after sizing may prevent neck cracking on firing and even neck tension leading to improved accuracy in extreme cases. Sent from my iPhone...

    Liked On: 17-04-2023, 04:47 PM

13. 
    mopheadrob liked post by zimmer On thread : Annealing after sizing?

    Always anneal after every firing and b4 any sizing. I deprime, brush clean inside the neck, clean the outside of the neck and shoulder with Krazy Kloth, clean the primer pocket, and then anneal....

    Liked On: 17-04-2023, 04:47 PM

14. 
    mopheadrob liked post by dannyb On thread : Annealing after sizing?

    I've always annealed before sizing, can't say I've heard of annealing after sizing ?

    Liked On: 17-04-2023, 04:46 PM

15. 
    mopheadrob liked post by chainsaw On thread : Annealing after sizing?

    I re-size either FL or neck then anneal. Works for me. And start annealing after 2 or 3 firings.

    Liked On: 17-04-2023, 04:46 PM

Page 15 of 49 First 1234567891011121314151617181920212223242526272829 ... Last

• Jump to page: