NAKED_GOOSE
Member

267 Likes

Page 6 of 18 First 123456789101112131415161718 Last

• Jump to page:

1. 
   NAKED_GOOSE liked post by akaroa1 On thread : DIY Fibre wads?

   The A and B grade is the same density just prettier For punches just buy good individual ones from and engineering supplier Don't waste your time on cheap sets and crap imports The...

   Liked On: 26-10-2023, 11:55 AM

2. 
   NAKED_GOOSE liked post by Tedz50 On thread : DIY Fibre wads?

   https://www.shuk.co.nz/ They have wool felt in various thicknesses as well. 236077 236078 236079

   Liked On: 26-10-2023, 07:45 AM

3. 
   NAKED_GOOSE liked post by rupert On thread : DIY Fibre wads?

   I tried a simple home made hit it with a club hammer type punch for 20ga wads using Pinex wallboard which is about 10mm thick. It seemed to work a bit but the edge of the punch rolled over after a...

   Liked On: 24-10-2023, 04:26 PM

4. 
   NAKED_GOOSE liked post by Marty Henry On thread : DIY Fibre wads?

   Card, greased pinex then shot is my version the grease sort of glues the wad together and makes it much easier to load. Pin in the wad and a quick dip in beeswax /lard 1:1 then allow to harden .

   Liked On: 24-10-2023, 04:20 PM

5. 
   NAKED_GOOSE liked post by zimmer On thread : DIY Fibre wads?

   I think 25 mm is the old thick Pinex, not the Michelangelo version of ceiling tiles. To make the holesaw into a knife rather than a messy ripping saw. Effectively a rotary wadcutter like my mate's.

   Liked On: 24-10-2023, 04:00 PM

6. 
   NAKED_GOOSE liked post by zimmer On thread : DIY Fibre wads?

   The cutter I used belonging to a mate was specially made to cut 12g wads. Back then those sorts of things were available. It had a sprung centre plunger that popped the wad out once cut. Even if...

   Liked On: 24-10-2023, 03:50 PM

7. 
   NAKED_GOOSE liked post by zimmer On thread : DIY Fibre wads?

   I used to use ceiling Pinex. Can you still get Pinex though? Mate had a special 12g cutter that you put in a drill press for making wads. IIRC I had one thin stiff overpowder wad (cut with correct...

   Liked On: 24-10-2023, 03:30 PM

8. 
   NAKED_GOOSE liked post by tac a1 On thread : Useing the firearms register

   So, just rang the registry number as I cant get the bloody thing to work. Wont accept password. Spoke to a really nice Indian lady who was immensely helpful. All guns registered in 15 minutes....

   Liked On: 20-10-2023, 03:10 PM

9. 
   NAKED_GOOSE liked post by ishoot10s On thread : Useing the firearms register

   My god. The database just full of rubbish already, the chumps. When I tried to find a match for an old single barrel 12 ga Champion, I get a choice of a single shot, or an 8 shot! Since when did Iver...

   Liked On: 20-10-2023, 02:29 PM

10. 
    NAKED_GOOSE liked post by blip On thread : Useing the firearms register

    I wonder would fuckedifiknow would pass as a serial no.:)

    Liked On: 20-10-2023, 02:08 PM

11. 
    NAKED_GOOSE liked post by Flyblown On thread : Raising a magpie chick - any tips

    Dog food - dog roll I assume? Talk to it - ok. I already talk to myself a lot so talking to a bird is probably a step in the right direction. It will possibly cure you of shooting magpies -...

    Liked On: 20-10-2023, 11:29 AM

12. 
    NAKED_GOOSE liked post by Micky Duck On thread : scofemupdelishimo duck balls

    The fruit is for......scale lol235611

    Liked On: 19-10-2023, 11:08 AM

13. 
    NAKED_GOOSE liked post by norsk On thread : Motorbike checkover

    One of the best things I have ever done was buying a motorcycle.

    Liked On: 18-10-2023, 08:02 AM

14. 
    NAKED_GOOSE liked post by 7mm tragic On thread : Getting back to living off the land.....

    Me too, gotta say it looked better before it was cooked.

    Liked On: 17-10-2023, 05:06 PM

15. 
    NAKED_GOOSE liked post by timattalon On thread : Motorbike checkover

    One suggestion from someone who has a couple.....try to get something pst 2000 if you are wanting to ride more than just summer months....6 month wof get old fast- its ok if you use it for 6 months...

    Liked On: 17-10-2023, 09:26 AM

Page 6 of 18 First 123456789101112131415161718 Last

• Jump to page: