NCGNSMITH
Member

102 Likes

Page 3 of 7 First 1234567 Last

• Jump to page:

1. 
   dannyb liked post by NCGNSMITH On thread : Best paint for CF stock

   It’s is a paint from dulux comes in different colours and effects in a spray can https://www.dulux.co.nz/paint/duramax/duramax-marble-effect-spray-paint/

   Liked On: 17-07-2025, 07:55 PM

2. 
   kristopher liked post by NCGNSMITH On thread : Boyds Stocks ordering

   Could always order a one off direct The gun parts amount was put up from $100 to $500 USD With out needing a permit I ordered one 4 months ago had to work out time difference and Call them...

   Liked On: 17-07-2025, 07:04 PM

3. 
   Frogfeatures liked post by NCGNSMITH On thread : Different 22 brand question

   Some of the geco stuff I found was waxy And gave issues in customers semi autos Would light strike due to wax/grease stopping it From fully seating in chamber then firing pin hits the rim And...

   Liked On: 14-07-2025, 12:13 AM

4. 
   308 liked post by NCGNSMITH On thread : Different 22 brand question

   Some of the geco stuff I found was waxy And gave issues in customers semi autos Would light strike due to wax/grease stopping it From fully seating in chamber then firing pin hits the rim And...

   Liked On: 13-07-2025, 11:23 PM

5. 
   NO4 liked post by NCGNSMITH On thread : Barrel channel clearance for free floated barrel

   You can cover the barrel in heat shrink 1-2 pieces thick depending On clearance you after and release agent And bed the forend if it annoys you I do them quite regularly for customers Just...

   Liked On: 13-07-2025, 03:27 PM

6. 
   SneedFeed liked post by NCGNSMITH On thread : Howa 223 Blued/walnut with Hardy Barrel

   Have threaded a few now inc Danny’s and every one had a off center bore When they were shortened and rethreaded the last one being particularly Bad seemed to shoot ok but one of them was bad...

   Liked On: 12-07-2025, 12:03 AM

7. 
   Shamus_ liked post by NCGNSMITH On thread : Barrel channel clearance for free floated barrel

   You can cover the barrel in heat shrink 1-2 pieces thick depending On clearance you after and release agent And bed the forend if it annoys you I do them quite regularly for customers Just...

   Liked On: 06-07-2025, 04:21 PM

8. 
   schwen liked post by NCGNSMITH On thread : Mossberg 500 Firing Pin

   Cut a round remove all the guts shot wad powder and push the muzzle into a rag folded over A few times on the ground and it will hardly make a noise

   Liked On: 12-06-2025, 09:05 AM

9. 
   Jhon liked post by NCGNSMITH On thread : Mossberg 500 Firing Pin

   Cut a round remove all the guts shot wad powder and push the muzzle into a rag folded over A few times on the ground and it will hardly make a noise

   Liked On: 10-06-2025, 11:44 AM

10. 
    timattalon liked post by NCGNSMITH On thread : Reloading Service Canty

    Andrew Torrington The New Zealand bullet company He does custom load development and canty based Phone 021 958 137 torrington,andrew@gmail.com

    Liked On: 02-06-2025, 01:35 AM

11. 
    Barnes130 liked post by NCGNSMITH On thread : Reloading Service Canty

    Andrew Torrington The New Zealand bullet company He does custom load development and canty based Phone 021 958 137 torrington,andrew@gmail.com

    Liked On: 01-06-2025, 09:16 PM

12. 
    bluebaiter222 liked post by NCGNSMITH On thread : Reloading Service Canty

    Andrew Torrington The New Zealand bullet company He does custom load development and canty based Phone 021 958 137 torrington,andrew@gmail.com

    Liked On: 31-05-2025, 11:58 AM

13. 
    Old_School liked post by NCGNSMITH On thread : Primers burnng through

    Pin shape or protrusion Pull it apart push the pin out of the breach face As far as you can and measure how far they protrude Also they want to be nicely domed not sharp on the nose of the pin

    Liked On: 18-05-2025, 06:01 PM

14. 
    Finnwolf liked post by NCGNSMITH On thread : Brass on bolt face

    Not uncommon on a fresh bluing job or parkerising ect More so if you hit them in the bead blast tank first Nothing to worry about Definitely not enough to change headspace Or firing pin...

    Liked On: 17-03-2025, 11:49 AM

15. 
    csmiffy liked post by NCGNSMITH On thread : Tikka 34mm rings

    Sports match, uk made rings super solid direct fit Way cheaper then a lot of the other offerings

    Liked On: 12-01-2025, 04:43 PM

Page 3 of 7 First 1234567 Last

• Jump to page: