No.3
Member

1736 Likes

Page 99 of 116 First ... 49858687888990919293949596979899100101102103104105106107108109110111112113 ... Last

• Jump to page:

1. 
   Moa Hunter liked post by No.3 On thread : Marlin Ballard restoration

   A pump repair I had to do a while back looked something like that - couple of pins cracked and flogged out which prevented the parts engaging correctly and the end result was a timing issue that...

   Liked On: 19-10-2022, 04:23 PM

2. 
   Micky Duck liked post by No.3 On thread : 300 Rounds go missing

   Problem here is that the real world doesn't nicely line up with Police very black/white ideas of "WHAT MUST HAPPEN". You can't stop shipping firearms and ammo, even for Police. Any time you entrust...

   Liked On: 18-10-2022, 03:39 PM

3. 
   Moa Hunter liked post by No.3 On thread : Pack advice

   With a larger pack, as long as it doesn't have big 'bellows' type pockets on the outside you can always fit compression straps to compress it right down. I look for lid straps that come from the...

   Liked On: 18-10-2022, 03:19 PM

4. 
   Bol Tackshin liked post by No.3 On thread : 300 Rounds go missing

   Problem here is that the real world doesn't nicely line up with Police very black/white ideas of "WHAT MUST HAPPEN". You can't stop shipping firearms and ammo, even for Police. Any time you entrust...

   Liked On: 18-10-2022, 02:31 PM

5. 
   Micky Duck liked post by No.3 On thread : show us your chainsaws

   Yep, good saw - done a fair bit of time on them. I currently have a 361, rate it higher for the work I have now than the 044's but it's purely down to the bulk/weight and I reckon it spins a bit...

   Liked On: 16-10-2022, 07:54 AM

6. 
   Pengy liked post by No.3 On thread : Mitsi D5

   Should be able to plug into that then if they have the correct scan tool. Given the fact it's just been serviced, it could point to (or maybe better to say in my opinion it would tend to point...

   Liked On: 15-10-2022, 09:11 PM

7. 
   Pengy liked post by No.3 On thread : Mitsi D5

   So - devil's advocate, did they put the correct fluid in it? CVT's sh1t themselves proper like and in very short order if filled with the wrong fluid (ATF looks and smells the same and if the boys...

   Liked On: 15-10-2022, 08:43 PM

8. 
   Dundee liked post by No.3 On thread : Lets See The Transport havn a Oops moment

   I wish I had evidence of the worst whoopsie I did - I was in one of my old company work utes, just popped up to the tank that supplied the plant area with water and gave the ballcock the obligatory...

   Liked On: 14-10-2022, 07:53 AM

9. 
   XR500 liked post by No.3 On thread : Toyota or nissan V6

   I suspect that the cost of parts isn't that much higher i.e. the Ranger to replace fuel rail, 5 injectors and injection pump inc. labour = $8500 or so - the Safari to do 6 injectors injection pump...

   Liked On: 14-10-2022, 04:11 AM

10. 
    Ross Nolan liked post by No.3 On thread : need some suggestions of choosing between Ford Everest & Land Cruiser

    You never get the perfect setup of rear doors on a vehicle, I think it's one of those impossible things in the world! Barn doors end up being a pain loading or in wind, the tailgate style can get in...

    Liked On: 13-10-2022, 10:26 AM

11. 
    rugerman liked post by No.3 On thread : Lets See The Transport havn a Oops moment

    I wish I had evidence of the worst whoopsie I did - I was in one of my old company work utes, just popped up to the tank that supplied the plant area with water and gave the ballcock the obligatory...

    Liked On: 12-10-2022, 06:58 PM

12. 
    RV1 liked post by No.3 On thread : Torqueing screws for cheapskates

    Having said that, I would respectfully suggest that your particular hand is a lot more highly experienced at hitting the 'correct' torque than someone who's come off a lifetime of pedalling an office...

    Liked On: 12-10-2022, 02:10 PM

13. 
    Micky Duck liked post by No.3 On thread : Case Inspection. Anything of note here, folks ?

    Or maybe US clean, which does the same thing less polishing and pin impacts. The comment about life is pretty much spot on, I'd be cleaning them up and doing the case length trim and checking case...

    Liked On: 11-10-2022, 08:51 PM

14. 
    Micky Duck liked post by No.3 On thread : Torqueing screws for cheapskates

    Having said that, I would respectfully suggest that your particular hand is a lot more highly experienced at hitting the 'correct' torque than someone who's come off a lifetime of pedalling an office...

    Liked On: 11-10-2022, 04:50 PM

15. 
    mudgripz liked post by No.3 On thread : need some suggestions of choosing between Ford Everest & Land Cruiser

    This in manual or auto? I know the manuals have an issue with loading in 6th - don't tow in 6th rah rah. But I know of a lot of Toyota boxes dying early too so who knows, I think your comment about...

    Liked On: 11-10-2022, 11:27 AM

Page 99 of 116 First ... 49858687888990919293949596979899100101102103104105106107108109110111112113 ... Last

• Jump to page: