No.3
Member

1518 Likes

Page 51 of 102 First ... 3738394041424344454647484950515253545556575859606162636465101 ... Last

• Jump to page:

1. 
   Micky Duck liked post by No.3 On thread : Tuatahi axe project - small axe / hatchet for hunting, tramping, fishing etc

   Hows it look on the handle after a serious amount of work? I had one similar to this design with the front bottom of the eye hole is cut away, and it was a bugger for working loose on the haft. All...

   Liked On: 31-05-2023, 12:15 PM

2. 
   Moa Hunter liked post by No.3 On thread : 4.2tdi

   Not unusual, the engine is out of the Nissan light truck line so built a lot heavier than automotive light vehicle engines. It runs a lot lighter loaded than the equivalent car engine, with heavier...

   Liked On: 29-05-2023, 12:51 PM

3. 
   Trout liked post by No.3 On thread : 4.2tdi

   The earlier mounts were better, I put the original 'tired' ones back in for the time it took to build a set that won't break. The other three failed at the adhesion of the rubber to the metal...

   Liked On: 29-05-2023, 11:12 AM

4. 
   Micky Duck liked post by No.3 On thread : 4.2tdi

   Not unusual, the engine is out of the Nissan light truck line so built a lot heavier than automotive light vehicle engines. It runs a lot lighter loaded than the equivalent car engine, with heavier...

   Liked On: 29-05-2023, 10:57 AM

5. 
   Calvnz1 liked post by No.3 On thread : Tumbler or Sonic cleaner

   Each do different things, ultrasonic will clean inside and out and get cases completely clean including the thin layer that stops the case tarnishing. Tumbling will remove adhered carbon such as...

   Liked On: 28-05-2023, 08:52 PM

6. 
   bigbear liked post by No.3 On thread : Stihl Chainsaw

   Yeah, 291 and 261 take the same size chain/bar as specc'd from the factory (.325 chain) where the 391 is the larger 3/8 'low pro' pitch chain. 261 is a 'pro' model - the cylinder is bolted down to...

   Liked On: 26-05-2023, 09:08 PM

7. 
   HOLDINGELM liked post by No.3 On thread : Remington 700 SA chassis stock

   Probably the latter - firearms that use AR-spec parts like stocks and mags have all but consumed those too.

   Liked On: 26-05-2023, 05:58 PM

8. 
   Shamus_ liked post by No.3 On thread : Horrible pipes

   Nope - the auctions have ammo in the same place as firearms so the firearms must be deactivated. Or the ammo locked away or something... It's to my mind pretty much a common sense thing - we...

   Liked On: 26-05-2023, 12:18 PM

9. 
   zimmer liked post by No.3 On thread : Stihl Chainsaw

   How much use are you going to put it to? The 261 is a bloody nice saw, I have the MS260 and MS361 combo currently but have have a range of other Stihls, Husqy's, Makita's, etc etc. If you are a few...

   Liked On: 25-05-2023, 09:27 PM

10. 
    Micky Duck liked post by No.3 On thread : Stihl Chainsaw

    Sounds like 261 it is then. Will be fine for what you are doing, especially if you have access to the bigger saw. That's the reason I ended up with the 361 - figured it would be a 'do everything'...

    Liked On: 25-05-2023, 09:06 PM

11. 
    Micky Duck liked post by No.3 On thread : Stihl Chainsaw

    How much use are you going to put it to? The 261 is a bloody nice saw, I have the MS260 and MS361 combo currently but have have a range of other Stihls, Husqy's, Makita's, etc etc. If you are a few...

    Liked On: 25-05-2023, 05:25 PM

12. 
    timattalon liked post by No.3 On thread : A right royal rogering - Nightforce

    Have you seen the price of tiddlywinks chips lately???????????? (Obviously not...)

    Liked On: 25-05-2023, 04:03 AM

13. 
    Micky Duck liked post by No.3 On thread : A right royal rogering - Nightforce

    Basically the approved distributor will be likely violating their contract with the manufacturer if they parallel import outside of the approved supply line. They can do it, but it risks the...

    Liked On: 24-05-2023, 06:42 PM

14. 
    madjon_ liked post by No.3 On thread : A right royal rogering - Nightforce

    Basically the approved distributor will be likely violating their contract with the manufacturer if they parallel import outside of the approved supply line. They can do it, but it risks the...

    Liked On: 24-05-2023, 06:21 PM

15. 
    mikee liked post by No.3 On thread : A right royal rogering - Nightforce

    Basically the approved distributor will be likely violating their contract with the manufacturer if they parallel import outside of the approved supply line. They can do it, but it risks the...

    Liked On: 24-05-2023, 06:19 PM

Page 51 of 102 First ... 3738394041424344454647484950515253545556575859606162636465101 ... Last

• Jump to page: