No washers are required with the cyclone since it does not need to be clocked. It only needs a minimum shoulder of about 2mm over the thread to square up on. One of the things that worried me about...
Liked On: 20-06-2016, 05:47 PM
Thanks for the comments. All the muzzle devices are A cat compliant. All are closed at the front unlike "flash suppressors" which are specifically designed to "suppress" the flash. I have renamed...
Liked On: 18-06-2016, 07:35 PM
Thanks for the comments. All the muzzle devices are A cat compliant. All are closed at the front unlike "flash suppressors" which are specifically designed to "suppress" the flash. I have renamed...
Liked On: 18-06-2016, 12:49 PM
The other chrony was averaging 52 fps faster but I didn't have all the shot data on that chrony. It is factory ammo made by Laupua. I would be happy to run whatever you want to run through it. The...
Liked On: 28-04-2016, 11:53 PM
No, I didn't miss the point. As I said, he is welcome to bring his rifle and we will test my can with any ammo he wants. Strength of the primary blast chamber is not an issue. The way it is...
Liked On: 28-04-2016, 02:01 PM
No, I didn't miss the point. As I said, he is welcome to bring his rifle and we will test my can with any ammo he wants. Strength of the primary blast chamber is not an issue. The way it is...
Liked On: 28-04-2016, 11:41 AM
The group using these have had them in service for about 2 years now. The life depends on the rate of fire. A lot of FA fire will reduce their life and that of the barrel considerably. Currently...
Liked On: 27-04-2016, 10:34 AM
Here are a few numbers that may be helpful. Using a BK 2209 meter and 4136 mic calibrated with a BK 4228 Piston phone located 1 meter left of the muzzle and 1.6 meters above the ground. 20" PWS...
Liked On: 10-04-2016, 10:43 AM
Here are a few numbers that may be helpful. Using a BK 2209 meter and 4136 mic calibrated with a BK 4228 Piston phone located 1 meter left of the muzzle and 1.6 meters above the ground. 20" PWS...
Liked On: 05-04-2016, 10:02 PM
Here are the cans and a prototype cover. I never built anything with fabrics before so this is mainly about materials selection and thread design to keep as much of the kevlar thread outside the...
Liked On: 18-02-2016, 11:37 AM
Brinell is a hardness testing method (http://www.hardnesstesters.com/Applications/Brinell-Hardness-Testing.aspx). Wear plates come in a variety of "brand" names including bisalloy. I have built...
Liked On: 06-10-2015, 03:30 PM
Brinell is a hardness testing method (http://www.hardnesstesters.com/Applications/Brinell-Hardness-Testing.aspx). Wear plates come in a variety of "brand" names including bisalloy. I have built...
Liked On: 06-10-2015, 03:17 PM
Gimp, the monthly up date is send me an email. The can is ready for test as a prototype. I need to run a set of sound tests this weekend to make sure I fixed one issue and then you can run it. It...
Liked On: 16-07-2015, 06:22 AM
Gimp, the monthly up date is send me an email. The can is ready for test as a prototype. I need to run a set of sound tests this weekend to make sure I fixed one issue and then you can run it. It...
Liked On: 14-07-2015, 07:28 PM
Cheers for the confidence, Digit! I have costing underway and a design half finished. The design goal will be a reasonable priced can that sounds good and is light for bolt action rifle rate of...
Liked On: 28-05-2015, 09:52 AM