Oldbloke
Member

243 Likes

Page 16 of 17 First ... 234567891011121314151617 Last

• Jump to page:

1. 
   Micky Duck liked post by Oldbloke On thread : Shooting rest in tussock country

   I've tried a few different types of rests/shooting stix over the years. I've found this the best for me. I used 8mm alluminium tubing from bunnings for the long ones. But 12mm wooden dowel is...

   Liked On: 24-10-2022, 03:41 PM

2. 
   charliehorse liked post by Oldbloke On thread : Sierra & Hornady bullet sections

   Here is a 180gr Hornady interlock 3070 i sectioned and then melted the lead.

   Liked On: 21-10-2022, 12:30 PM

3. 
   rupert liked post by Oldbloke On thread : Sierra & Hornady bullet sections

   Here is a 180gr Hornady interlock 3070 i sectioned and then melted the lead.

   Liked On: 21-10-2022, 08:23 AM

4. 
   veitnamcam liked post by Oldbloke On thread : Sierra & Hornady bullet sections

   Here is a 180gr Hornady interlock 3070 i sectioned and then melted the lead.

   Liked On: 21-10-2022, 07:57 AM

5. 
   caberslash liked post by Oldbloke On thread : Sierra & Hornady bullet sections

   Here is a 180gr Hornady interlock 3070 i sectioned and then melted the lead.

   Liked On: 21-10-2022, 12:00 AM

6. 
   Moa Hunter liked post by Oldbloke On thread : HELP! Primers

   I put one of these in with every box of ammo I load. Also record in a note book.

   Liked On: 20-10-2022, 11:07 PM

7. 
   dannyb liked post by Oldbloke On thread : HELP! Primers

   I put one of these in with every box of ammo I load. Also record in a note book.

   Liked On: 20-10-2022, 10:51 PM

8. 
   Moa Hunter liked post by Oldbloke On thread : Washing hunting clothes. (Real men can scroll on past)

   All the supermarkets have it here in Victoria. All about the same price. 208363

   Liked On: 19-10-2022, 04:10 PM

9. 
   madjon_ liked post by Oldbloke On thread : Reloading components availability

   So just wondering how you blokes are going getting hold of components for the last year or so? Over here in OZ for some time ADI powder was hard to get but slowly improving now. ADI had some...

   Liked On: 01-05-2022, 02:12 PM

10. 
    shooternz liked post by Oldbloke On thread : "Best" Digital scales around

    Digital scales have a bad habit of being unreliable and expensive. I would stick to a decent beam balance and if they are slow settling add some magnets (or replace with stronger ones) to the...

    Liked On: 01-05-2022, 10:36 AM

11. 
    Micky Duck liked post by Oldbloke On thread : Reloading components availability

    So just wondering how you blokes are going getting hold of components for the last year or so? Over here in OZ for some time ADI powder was hard to get but slowly improving now. ADI had some...

    Liked On: 30-04-2022, 09:10 PM

12. 
    Micky Duck liked post by Oldbloke On thread : "Best" Digital scales around

    Digital scales have a bad habit of being unreliable and expensive. I would stick to a decent beam balance and if they are slow settling add some magnets (or replace with stronger ones) to the...

    Liked On: 30-04-2022, 06:30 PM

13. 
    norsk liked post by Oldbloke On thread : "Best" Digital scales around

    Digital scales have a bad habit of being unreliable and expensive. I would stick to a decent beam balance and if they are slow settling add some magnets (or replace with stronger ones) to the...

    Liked On: 30-04-2022, 12:26 AM

14. 
    Borris liked post by Oldbloke On thread : Reloading components availability

    So just wondering how you blokes are going getting hold of components for the last year or so? Over here in OZ for some time ADI powder was hard to get but slowly improving now. ADI had some...

    Liked On: 25-04-2022, 02:46 AM

15. 
    Pete_D liked post by Oldbloke On thread : 6.5 Reduced loads

    AR2206H. You can use this powder for reduced loads. Load down to 60% of the max listed load. Have a look on the ADI site. http://www.adi-powders.com.au/faq/#f21b4c284d0d2d9af

    Liked On: 20-08-2020, 08:38 AM

Page 16 of 17 First ... 234567891011121314151617 Last

• Jump to page: