Oldbloke
Member

243 Likes

Page 8 of 17 First 1234567891011121314151617 Last

• Jump to page:

1. 
   erniec liked post by Oldbloke On thread : Sierra Matchking 308 125gr HP for huntinf

   All good mate.

   Liked On: 05-10-2023, 08:07 PM

2. 
   Micky Duck liked post by Oldbloke On thread : Sierra Matchking 308 125gr HP for huntinf

   Micky Duck Yes, i will try that. But currently im thinking that 1" is 25.4mm. Sooo, get a square lump of 1" steel and drill a 5/16" (0.312") hole through. File them roughly in the mini vice,...

   Liked On: 04-10-2023, 03:44 PM

3. 
   Micky Duck liked post by Oldbloke On thread : Time to re-introduce a paying for deer/goat tail scheme?

   Yes, the "cobra bounty" story is interesting. As usual "greed" takes over. But a fox bounty of $10 seems to work in Victoria. (AU) ($10 currently buys abt 5ltrs of diesel) Its enough to create an...

   Liked On: 04-10-2023, 09:47 AM

4. 
   rupert liked post by Oldbloke On thread : Sierra Matchking 308 125gr HP for huntinf

   Completed 25. File in a thingamajig. Course file then a couple of strokes with i fine file. Obviously bit slow. Length variation was about 0.3mm. So after checking with vernier 3 or 4 got a couple of...

   Liked On: 03-10-2023, 03:14 PM

5. 
   rossi.45 liked post by Oldbloke On thread : Sierra Matchking 308 125gr HP for huntinf

   Thx for that Flyblown. Great explanation and just the info im after. Now thinking that perhaps i should sell them.

   Liked On: 28-09-2023, 09:21 AM

6. 
   Micky Duck liked post by Oldbloke On thread : Sierra Matchking 308 125gr HP for huntinf

   Big jump in cost tho. I do like the idea, i can carry a couple of 180gr loads.

   Liked On: 23-09-2023, 08:13 PM

7. 
   rupert liked post by Oldbloke On thread : Sierra Matchking 308 125gr HP for huntinf

   Looking around lots of conflicting info. This bloke drilled the tip out and got good results. Just bought 500 for $150 delivered. Ill only be pushing them at about 2650fps See the 6 minute...

   Liked On: 22-09-2023, 03:00 PM

8. 
   Moa Hunter liked post by Oldbloke On thread : Cast Lead Thread ?

   My tester in action.

   Liked On: 15-09-2023, 09:29 AM

9. 
   Moa Hunter liked post by Oldbloke On thread : Cast Lead Thread ?

   DIY BRINELL HARDNESS TESTER. ( BHN ) Just found this thread. As mentioned earlier there are a few ways to do this. Lee test kit. I haven't used this but reports suggest it works fine but a but...

   Liked On: 15-09-2023, 09:28 AM

10. 
    Trout liked post by Oldbloke On thread : Re visit on 30-06

    That has been my understanding for many years. Have read it many times, but have not tried 110gr myself. Same for 308. The 110gr are simply too short. That's why my light load uses 130gr.

    Liked On: 09-09-2023, 10:43 AM

11. 
    Micky Duck liked post by Oldbloke On thread : Re visit on 30-06

    That has been my understanding for many years. Have read it many times, but have not tried 110gr myself. Same for 308. The 110gr are simply too short. That's why my light load uses 130gr.

    Liked On: 09-09-2023, 12:16 AM

12. 
    Happy Jack liked post by Oldbloke On thread : Re visit on 30-06

    I'm loading 49gr AR2208. 130gr Hornady SP. Nice groups too. About 2700fps I think 22" barrel. Very, very mild to shoot but drop fallow ok.

    Liked On: 06-09-2023, 09:19 PM

13. 
    dannyb liked post by Oldbloke On thread : Re visit on 30-06

    I'm loading 49gr AR2208. 130gr Hornady SP. Nice groups too. About 2700fps I think 22" barrel. Very, very mild to shoot but drop fallow ok.

    Liked On: 06-09-2023, 08:21 PM

14. 
    rupert liked post by Oldbloke On thread : Cast Lead Thread ?

    My tester in action.

    Liked On: 30-08-2023, 11:01 PM

15. 
    11mms liked post by Oldbloke On thread : First attempt at reloading. Thoughts please.

    If you listen to some, by the time you find the best load you will run out of components, perhaps may not be able to buy more identical components and and need to rebarrel because the original is...

    Liked On: 24-08-2023, 07:07 PM

Page 8 of 17 First 1234567891011121314151617 Last

• Jump to page: