PaulNZ
Member

408 Likes

Page 16 of 28 First ... 2345678910111213141516171819202122232425262728 Last

• Jump to page:

1. 
   rewa liked post by PaulNZ On thread : Walnut Stock Build

   One more post and this’ll be up to date with where I’m actually at. If I was writing this chronologically, there should actually be a post in between thinking the pattern stock was done and then...

   Liked On: 09-07-2021, 02:11 PM

2. 
   rewa liked post by PaulNZ On thread : Walnut Stock Build

   So some of the changes I made to the stock at this point were to reduce LOP by ¼”, flatten off the palm swell slightly, and deepen and extend the comb fluting. All easily done. But I also couldn’t...

   Liked On: 09-07-2021, 02:08 PM

3. 
   rewa liked post by PaulNZ On thread : Walnut Stock Build

   Another few snapshots from the milling for your interest. Note that these are all with the wood still wet – the colour did change considerably after drying. https://i.imgur.com/uGWBeQB.jpg ...

   Liked On: 09-07-2021, 02:06 PM

4. 
   rewa liked post by PaulNZ On thread : Walnut Stock Build

   Inletting of barrelled action and bottom metal has gone as far as I'm going to take it on the mill. Time to break out the inletting black and sharpen up the chisels and scrapers for the final...

   Liked On: 09-07-2021, 01:48 PM

5. 
   HILLBILLYHUNTERS liked post by PaulNZ On thread : Walnut Stock Build

   Inletting of barrelled action and bottom metal has gone as far as I'm going to take it on the mill. Time to break out the inletting black and sharpen up the chisels and scrapers for the final...

   Liked On: 08-07-2021, 08:40 PM

6. 
   Tuidog liked post by PaulNZ On thread : Walnut Stock Build

   Inletting of barrelled action and bottom metal has gone as far as I'm going to take it on the mill. Time to break out the inletting black and sharpen up the chisels and scrapers for the final...

   Liked On: 08-07-2021, 02:09 PM

7. 
   canross liked post by PaulNZ On thread : Baikal single shot rebarrel - Anyone done this?

   Great description of your lapping setup. I've looked into bore lapping before but never actually done it. Considered it for my problematic grey birch barrel to remove the bore constriction, but...

   Liked On: 22-06-2021, 11:59 AM

8. 
   HILLBILLYHUNTERS liked post by PaulNZ On thread : Walnut Stock Build

   Well, after working through a long list of other distractions I've finally made the time to give my stock a bit more attention. Not a whole lot, but at least it's forward progress! Getting ready...

   Liked On: 18-06-2021, 09:27 PM

9. 
   17brno liked post by PaulNZ On thread : Walnut Stock Build

   Well, after working through a long list of other distractions I've finally made the time to give my stock a bit more attention. Not a whole lot, but at least it's forward progress! Getting ready...

   Liked On: 18-06-2021, 08:49 PM

10. 
    Moa Hunter liked post by PaulNZ On thread : Walnut Stock Build

    Well, after working through a long list of other distractions I've finally made the time to give my stock a bit more attention. Not a whole lot, but at least it's forward progress! Getting ready...

    Liked On: 18-06-2021, 07:45 PM

11. 
    Mathias liked post by PaulNZ On thread : Walnut Stock Build

    Well, after working through a long list of other distractions I've finally made the time to give my stock a bit more attention. Not a whole lot, but at least it's forward progress! Getting ready...

    Liked On: 18-06-2021, 04:47 PM

12. 
    Joe_90 liked post by PaulNZ On thread : Walnut Stock Build

    Well, after working through a long list of other distractions I've finally made the time to give my stock a bit more attention. Not a whole lot, but at least it's forward progress! Getting ready...

    Liked On: 17-06-2021, 11:29 PM

13. 
    ROKTOY liked post by PaulNZ On thread : Walnut Stock Build

    Well, after working through a long list of other distractions I've finally made the time to give my stock a bit more attention. Not a whole lot, but at least it's forward progress! Getting ready...

    Liked On: 17-06-2021, 11:12 PM

14. 
    Ryan_Songhurst liked post by PaulNZ On thread : Walnut Stock Build

    Well, after working through a long list of other distractions I've finally made the time to give my stock a bit more attention. Not a whole lot, but at least it's forward progress! Getting ready...

    Liked On: 17-06-2021, 10:32 PM

15. 
    Noswal liked post by PaulNZ On thread : Voere Titan 222

    Very nice. I've been tempted to pick one up myself but I don't really have a need for the calibre at the moment. Would make a nice counterpart for my Voere .22. Interesting that they made their...

    Liked On: 11-06-2021, 02:56 PM

Page 16 of 28 First ... 2345678910111213141516171819202122232425262728 Last

• Jump to page: