Excellent drawing - posted in 2018 (post #18) here: https://www.nzhuntingandshooting.co.nz/f12/tell-me-about-wapiti-45511/index2.html so I don't think it's a recent sketch.
Liked On: 07-01-2024, 01:45 PM
I knew I'd read something about the widths of these mags before, and I just found the link: https://www.rimfirecentral.com/threads/french-unique-magazines.582725/#post-5370835 Seems like...
Liked On: 04-12-2023, 11:11 AM
I knew I'd read something about the widths of these mags before, and I just found the link: https://www.rimfirecentral.com/threads/french-unique-magazines.582725/#post-5370835 Seems like...
Liked On: 04-12-2023, 08:55 AM
Agree with the manufacturer and action type, but are you sure about the date range? I'd be thinking older than that.
Liked On: 03-12-2023, 08:04 PM
Some of the suggestions are trending towards smallish folding knives at over $100 - I'm not sure if that's what the OP is looking for, but if it is I'll throw in a suggestion for a Victorinox Hunter...
Liked On: 30-11-2023, 02:01 PM
Just my opinions, and assuming we're only talking about 1" rings: > Your alignment bars should be made from 1" bar (or tube, if the OD is accurate). Don't worry about making points - you'll get a...
Liked On: 10-10-2023, 02:08 PM
Just my opinions, and assuming we're only talking about 1" rings: > Your alignment bars should be made from 1" bar (or tube, if the OD is accurate). Don't worry about making points - you'll get a...
Liked On: 07-10-2023, 08:25 AM
Just my opinions, and assuming we're only talking about 1" rings: > Your alignment bars should be made from 1" bar (or tube, if the OD is accurate). Don't worry about making points - you'll get a...
Liked On: 07-10-2023, 07:21 AM
Just my opinions, and assuming we're only talking about 1" rings: > Your alignment bars should be made from 1" bar (or tube, if the OD is accurate). Don't worry about making points - you'll get a...
Liked On: 07-10-2023, 05:34 AM
Just my opinions, and assuming we're only talking about 1" rings: > Your alignment bars should be made from 1" bar (or tube, if the OD is accurate). Don't worry about making points - you'll get a...
Liked On: 07-10-2023, 04:25 AM
Sounds like there might be a story worth sharing there somewhere? Thanks to all who replied.
Liked On: 16-09-2023, 09:07 PM
Well I can finally close out this thread - I think I'm done. Stock is checkered (I don't think it came out too bad for a first effort), rifle is assembled and sighted in. A few photos for your...
Liked On: 06-06-2023, 10:36 PM
Just a variation on a theme, but after seeing your tests I think I've settled on the punch shape for my setup as well. I was using a 60deg lathe centre, but am now using a simple 28deg cone with a...
Liked On: 30-01-2023, 05:54 PM
Just a variation on a theme, but after seeing your tests I think I've settled on the punch shape for my setup as well. I was using a 60deg lathe centre, but am now using a simple 28deg cone with a...
Liked On: 30-01-2023, 02:59 PM
Just a variation on a theme, but after seeing your tests I think I've settled on the punch shape for my setup as well. I was using a 60deg lathe centre, but am now using a simple 28deg cone with a...
Liked On: 30-01-2023, 12:25 PM