Pete_D
Member

503 Likes

Page 11 of 34 First 12345678910111213141516171819202122232425 ... Last

• Jump to page:

1. 
   Pete_D liked post by Micky Duck On thread : Primer seating depth problems with new Lapua brass ?

   if they that hard to prime,consider giving pocket a twirl with deburring tool to put tiny taper into primer hole... DO NOT use lube. personally I would fire off the few you have loaded primer into,...

   Liked On: 22-08-2021, 08:09 PM

2. 
   Pete_D liked post by tetawa On thread : Primer seating depth problems with new Lapua brass ?

   Know their flash hole is 1.5mm, think standard is 2mm. Have found Lapua brass to be 'tight" in primer department, have you tried different small rifle primer?

   Liked On: 22-08-2021, 07:57 PM

3. 
   Pete_D liked post by zimmer On thread : Primer seating depth problems with new Lapua brass ?

   There's a new 21st Century on TradeMe at present. Looks like the seller us a retailer. I have the old model 21st Century - 3 thou per click but able to adjust half way between clicks.

   Liked On: 22-08-2021, 07:57 PM

4. 
   Pete_D liked post by gqhoon On thread : Primer seating depth problems with new Lapua brass ?

   I wouldn’t be using any lubricant that might compromise the detonation from the primer. I use a K&M hand primer (from Workshop Innovation), that gives good adjustability for primer seating depth....

   Liked On: 22-08-2021, 07:56 PM

5. 
   Pete_D liked post by rambo-6mmrem On thread : nzhs rimfire challenge

   have devised a little friendly forum shooting comp for the forum rules as follows 1 rimfire only 2 all targets shot at 50m or yards im not going to bitch about if its yards or meters so you are...

   Liked On: 18-08-2021, 08:48 PM

6. 
   Pete_D liked post by Lucky On thread : Oberndorf Mauser

   Thought some good rifle porn was required while in lockdown , so let’s start a thread on Pre-war Oberndorf sporting rifles , I’m sure a few of you will have 1 or 2 lurking in the gun cabinet , this...

   Liked On: 18-08-2021, 08:47 PM

7. 
   Pete_D liked post by VXN222 On thread : Trout Fishing: FREE Flys for Juniors

   Good stuff Pete_D I’ll get back to you and arrange a selection for your young fella. �� best thing I had growing up in a non fishing family was Parents who helped by getting in contact with family...

   Liked On: 18-08-2021, 12:51 PM

8. 
   Pete_D liked post by VXN222 On thread : Trout Fishing: FREE Flys for Juniors

   Gidday team, really like hearing about those of you working hard to get others into the sport. Looking to pass on a selection of trout flies to anyone getting their kids/mates into fishing. I’ve been...

   Liked On: 18-08-2021, 11:44 AM

9. 
   Pete_D liked post by Micky Duck On thread : Trout Fishing: FREE Flys for Juniors

   when you run short,let me know and I will whip up some dodgy creations too....dont loose many these days and need excuse to get tying kit out again.basic nymph patterns are just too easy to tie up....

   Liked On: 18-08-2021, 11:44 AM

10. 
    Pete_D liked post by planenutz On thread : Firearm licencing

    Yep... you got that right! Its a shame they've fucked up what was a pretty good system. The new forms now ask you to fill in answers to the questions they used to ask you during your interview so...

    Liked On: 18-07-2021, 02:15 PM

11. 
    Pete_D liked post by planenutz On thread : Firearm licencing

    Pete_D unfortunately you can no longer do this. When my son went through the process 4 years ago he carried out his Mountain Safety Course a couple of months before his 16th birthday and handed...

    Liked On: 17-07-2021, 04:06 PM

12. 
    Pete_D liked post by Cyclops On thread : Firearm licencing

    I believe you cannot complete the process before one's 16th birthday. It is a shame. My son got his learners driver license and FAL on his 16th birthday. I reminded him both were licenses that...

    Liked On: 14-07-2021, 07:08 PM

13. 
    Pete_D liked post by csmiffy On thread : 1912 Chilean Mauser - Bolt compatibility ???

    Graeme champion 067699608 He would most likely know the right fitment to just in case

    Liked On: 28-06-2021, 05:35 PM

14. 
    Pete_D liked post by Tentman On thread : 1912 Chilean Mauser - Bolt compatibility ???

    Hmmm - Thats a Springfield bolt, it won't fit a '98 . . . .

    Liked On: 27-06-2021, 09:53 PM

15. 
    Pete_D liked post by Russian 22. On thread : 1912 Chilean Mauser - Bolt compatibility ???

    I think it's worth waiting for the police import permit to come through. Read up on the new ITAR rules and if you're lucky a new bolt doesn't need an export permit as it's under the 500 usd dollar...

    Liked On: 27-06-2021, 09:53 PM

Page 11 of 34 First 12345678910111213141516171819202122232425 ... Last

• Jump to page: