r87mm
Member

221 Likes

Page 15 of 15 First 123456789101112131415

• Jump to page:

1. 
   MGNZ liked post by r87mm On thread : General approach to powder selection for a new load

   I agree with what's been said. I look for the top three powders in the book with good case fill and speed and then check the sites on the net to verify if others are using the same powders with good...

   Liked On: 28-11-2017, 10:17 AM

2. 
   Biggun708 liked post by r87mm On thread : Gongs...

   Was using 400bis for my 600m gong(what engineer said it was). 7mm rem 160-162 tmk,amax just chipped paint. eldx sometimes put a small dent. 300win mag 225 eldm almost went through! Can't rmbr whether...

   Liked On: 18-11-2017, 04:49 PM

3. 
   Steve123 liked post by r87mm On thread : Crappy Tikka T3 barrels??

   I would remove the barrel straight away before you wear it out as you know it's a great shooter. Then replace with an expensive unknown barrel that you need to spend heaps on trying to get it to...

   Liked On: 11-11-2017, 04:37 PM

4. 
   northdude liked post by r87mm On thread : Crappy Tikka T3 barrels??

   I would remove the barrel straight away before you wear it out as you know it's a great shooter. Then replace with an expensive unknown barrel that you need to spend heaps on trying to get it to...

   Liked On: 11-11-2017, 09:17 AM

5. 
   GWH liked post by r87mm On thread : Crappy Tikka T3 barrels??

   I would remove the barrel straight away before you wear it out as you know it's a great shooter. Then replace with an expensive unknown barrel that you need to spend heaps on trying to get it to...

   Liked On: 11-11-2017, 09:11 AM

6. 
   PERRISCICABA liked post by r87mm On thread : Bergara B14 HUNTER

   Yep got one in 300wm. Didn't like the trigger as was a bit heavy so put a second hand timney on it. Shoots pretty similar to yours by the looks. The original owner put a light weight alloy mag...

   Liked On: 28-10-2017, 04:10 PM

7. 
   PERRISCICABA liked post by r87mm On thread : .243 for 500m shots

   I'd go for the 4570. Let's face it at 300;yards on a smaller animal with a .243 job done. Now throwing a brick that far and expecting to hit it well that's a whole different story. Not against 243's...

   Liked On: 22-09-2017, 12:20 PM

8. 
   john m liked post by r87mm On thread : .243 for 500m shots

   I remember reading an article many years ago which basically said don't go by energy alone. The author talked about momentum as being the biggest factor in how a bullet penetrates and performs...

   Liked On: 10-09-2017, 10:32 AM

9. 
   199p liked post by r87mm On thread : carbon fiber vs steel

   Thanks guys. No real diffinative answer really. It seems there is no rule of thumb and carbon can be lighter but at a cost of stiffness. Having said that it can be very close depending on quality and...

   Liked On: 25-07-2017, 11:17 PM

10. 
    trooper90 liked post by r87mm On thread : 270wsm loads

    Started off with 130 sst's and accubonds, then tried 140sst's. They weren't any noticeably different from the lighter projectiles. More often than not were found in skin on off side of pigs or deer...

    Liked On: 15-02-2017, 06:02 PM

11. 
    nor-west liked post by r87mm On thread : 270wsm loads

    Started off with 130 sst's and accubonds, then tried 140sst's. They weren't any noticeably different from the lighter projectiles. More often than not were found in skin on off side of pigs or deer...

    Liked On: 03-02-2017, 08:57 PM

Page 15 of 15 First 123456789101112131415

• Jump to page: